Antonino Valenza

Antonino Valenza

Auto-generated profile, based on publicly available information

Antonino Valenza

Department of Engineering, University of Palermo, Viale delle Scienze, Edificio 6, 90128, Palermo, Italy

Research Focus & Metrics

Academic Career Length

33Years (1994-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 December 2018 in Journal of Applied Polymer Science
Verified
Journal Article
Closed access
PDF file
Luigi CalabreseLuigi Calabrese
Luigi Calabrese
Vincenzo FioreVincenzo Fiore
Vincenzo Fiore
TSTommaso Scalici
Tommaso Scalici
AVA. Valenza
A. Valenza

13 March 2019 in Journal of Natural Fibers
Verified
Journal Article
Closed access
Vincenzo FioreVincenzo Fiore
Vincenzo Fiore
GBG. Di Bella
G. Di Bella
AVA. Valenza
A. Valenza
The use of sheep wool as a filler of cement in order to produce mortar or plaster involves several advantages for environment and energy. Moreover, it is considered as a waste and, therefore, its use is characterized by low cost. The aim of this paper is to evaluate the influence of wool fibers on thermal conductivity and mechanical properties of cement. The samples were prepared using wool fibers, obtained from a breed of Sicilian sheep, with three different lengths (i.e., 1, 6, and 20 mm). Furthermore, in order to evaluate the influence of fiber content, the samples were prepared by varying the fiber weight fraction. The thermal conductivity of the samples was analyzed by using a heat flow meter, whereas the mechanical behavior was studied through compressive tests. In order to validate the thermal measurements, on the experimental data, two theoretical models were applied. The experimental results showed that wool fibers can be used within cementitious matrices to obtain mortars or plasters with enhanced thermal insulation properties. Nevertheless, noticeable decrements in the compressive strength are also found. Therefore, it is needed to find a compromise between these two aspects.

1 February 2022 in Composites Part B: Engineering
Verified
Journal Article
Closed access
Vincenzo FioreVincenzo Fiore
Vincenzo Fiore
Luigi CalabreseLuigi Calabrese
Luigi Calabrese
RMRiccardo Miranda
Riccardo Miranda
DBDionisio Badagliacco
Dionisio Badagliacco
CSC. Sanfilippo
C. Sanfilippo
Edoardo ProverbioEdoardo Proverbio
Edoardo Proverbio

1 April 2007 in Journal of Composite Materials
Verified
Journal Article
Closed access
AVA. Valenza
A. Valenza
Vincenzo FioreVincenzo Fiore
Vincenzo Fiore
Chiara BorsellinoChiara Borsellino
Chiara Borsellino
Luigi CalabreseLuigi Calabrese
Luigi Calabrese
Guido Di BellaGuido Di Bella
Guido Di Bella
The aim of this research is to investigate the pin/hole contact stress of a composite laminate and failure modes when submitted to tensile bearing tests. The limit loads and failure modes are evaluated as a function of pin diameter and hole position. Analyzing the joint geometry effect on the fracture mechanisms, a failure map is obtained, identifying three regions of typical failure modes of mechanically fastened joints. A theoretical approach is proposed to identify the field of each fracture mode to obtain a simple experimental methodology to support the design of a particular joint laminate. In addition, a simplified numerical model is proposed to evaluate near the hole the stress/strain distribution under tensile bearing load. This allows one to better understand the relevant dependence of the failure modes from the geometry of the joint for a given composite laminate.

1 January 2010 in Advanced Composite Materials
Verified
Journal Article
Closed access
AVA. Valenza
A. Valenza
Vincenzo FioreVincenzo Fiore
Vincenzo Fiore
Luigi CalabreseLuigi Calabrese
Luigi Calabrese
In this work, the failure mechanisms of GFRP/PVC foam core sandwich structures subjected to three-point bending are analysed. By varying the skin thickness (t) and the span length between supports ...

29 November 2021 in Journal of Applied Polymer Science
Verified
Journal Article
Open access
PDF file
Luigi CalabreseLuigi Calabrese
Luigi Calabrese
Vincenzo FioreVincenzo Fiore
Vincenzo Fiore
Elpida PiperopoulosElpida Piperopoulos
Elpida Piperopoulos
DBDionisio Badagliacco
Dionisio Badagliacco
DPDavide Palamara
Davide Palamara
Edoardo ProverbioEdoardo Proverbio
Edoardo Proverbio
The use of green materials such as natural fiber‐reinforced composites represents an increasingly stringent prerogative in the future planning of industrial and non‐industrial production. The optimization of these materials is the main aim of the current research, focused on the evaluation of the behavior of flax fiber reinforced composites exposed to isothermal adsorption and desorption cycles, at varying the partial pressure of water vapor (P/P0). For this purpose, the moisture uptake and the morphology changes of the composite material and their constituents were in situ monitored through a measurement protocol, by using a dynamic vapor sorption (DVS) analysis, coupled with an environmental scanning electron microscopy (ESEM) visual investigation. A dependence of moisture uptake and diffusivity on the composite morphology was clearly detected. In particular, no significant variation in the morphology of the specimen is noticed at low water vapor partial pressure (i.e., P/P0 up to 5.4%) due to the limited absorption capacity (i.e., lower than 1%). On the other hand, fibers morphology changes at increasing the partial pressure up to 25.1%, showing a sensitive increase in volume. This phenomenon becomes much more relevant for high relative humidity values (i.e., ~90%), reaching more than 6% of absorption capacity.