Fiber Bragg gratings (FBGs) are one of the most used optical fiber sensors and they have recently drawn the attention of several research groups for their potential applications in harsh radiation environments. Up to now, their performances have been mainly evaluated under ionizing radiations, such as X-rays or $\gamma $ -rays. We compare here the effects of different irradiation types, including X-rays, protons, and electrons, on type I FBGs written by UV laser exposure in Ge-, P/Ce-, and B/Ge-doped single-mode optical fibers. Different irradiation conditions were used according to the sources; 6-MeV electron irradiations were performed at a dose rate of 120 Gy(SiO 2 )/s up to an accumulated dose of 500 kGy; whereas for the 63-MeV protons, the estimated equivalent dose rate was of 0.75 Gy(SiO 2 )/s up to a total dose of 7 kGy. In order to compare their effects with those induced by X-rays, two irradiations with 45-keV photons were performed with different dose rates [0.75 and 60 Gy/s (SiO 2 )] up to a total dose of 10 and 500 kGy, respectively. We demonstrated that X-rays and protons induce comparable effects at doses of about 10 kGy, whereas the behavior under electron beam appears to be strongly dependent on the fiber composition. For example, the grating in the B/Ge co-doped fiber is the most sensitive to electrons and the most resistant to X-rays; whereas the FBG inscribed in the H 2 -loaded P/Ce co-doped fiber has exactly the opposite behavior.
9 February 2018 in IEEE Transactions on Nuclear Science
The impact of exposing an optical fiber to 6 MeV electrons on the performances of Optical Frequency Domain Reflectometry (OFDR) distributed sensors is investigated. Six different types of optical fibers with different core compositions and coatings have been tested: four fibers are metal-coated (copper, gold or aluminum) for high temperature (> 300°C) operations while the two others have Telecom-grade acrylate coatings for operation below 80°C. The fiber Rayleigh signature used to perform the OFDR sensing remains almost unaffected after an electron exposure. Indeed, the measured radiation-induced temperature errors are lower than about 3°C, close to the setup uncertainties, when the OFDR operates as a temperature sensor.
8 March 2019 in IEEE Transactions on Nuclear Science
We evaluate the potential of a new architecture of distributed optical fiber sensor (DOFS) to discriminate between the temperature and strain changes along a single optical fiber exposed to radiation. This DOFS exploits the measurements of both the Landau-Placzek ratio (LPR) and the Brillouin Frequency Shift (BFS) to achieve the discrimination between the two parameters on up to ten kilometers of fiber with a spatial resolution of 1 m. We demonstrate that the LPR remains unaffected up to MGy(SiO2) dose levels whereas the BFS is only slightly shifted by the radiation. The measured radiation-induced BFS is strongly reduced in radiation hardened fluorine-doped single-mode optical fibers. Combining the DOFS architecture and this fiber allows discriminating temperature and strain using a single optical fiber up to MGy dose levels.
thirteen different single-mode optical fibers have been experimentally and theoretically characterized highlighting the influence of the core and cladding dopants on their Brillouin signatures: Brillouin spectrum, temperature and strain coefficients. Tailoring the composition and the refractive index profile, optical fibers presenting Brillouin spectrum with multiple peaks have been designed, offering discrimination capabilities between the temperature and strain distributions along a single optical fiber.
2 April 2021 in IEEE Transactions on Nuclear Science
We investigate the radiation effects on a Brillouin based optical fiber sensor (OFS). This OFS exploits a single-mode optical fiber (SMF) having a Brillouin signature presenting multiple peaks. This specificity allows performing distributed and discriminated measurements of the temperature and strain time evolutions along the fiber. The particular structure (composition and refractive-index profile) of the investigated SMF was first conceived and optimized thanks to a home-made simulation tool to assess its capability to discriminate between the two environmental parameters. At the same time, it should also present a good radiation tolerance in order that the sensor could operate in radiation-rich environments (up to MGy levels). The modeled germanosilicate SMF has then been manufactured by the modified chemical vapor deposition process by iXblue and its sensing performances have been experimentally demonstrated. Samples of the SMF have been irradiated under steady state X-rays at a dose rate of 2.3 Gy(SiO2)/s up to 180 kGy at room temperature. The radiation tests showed that the Brillouin sensor can be implemented in such severe environments. At these dose levels, radiation induced errors are limited to ~3°C and ~0.15 με in the worst conditions. Finally, we discuss perspectives about possible new fiber structures to target even more challenging applications in terms of radiations and sensing requirements.
Brillouin signatures of 15 fibers are characterized experimentally and theoretically highlighting the core and cladding dopants influence. Tailoring the fiber composition and refractive index profile, multi-peak fibers allowing discriminating between temperature and strain appear feasible.