We investigated the radiation-induced attenuation (RIA) at 1550 nm under X-rays in two single-mode germanosilicate optical fibers (OFs): the Corning SMF-28e + and a homemade fiber manufactured by the Université Côte d'Azur in the framework of the CERTYF project. The RIA dependence on the injected power level of the probing signal is studied in order to analyze the photobleaching phenomenon at high doses [>100 kGy(SiO 2 )]. The Corning SMF-28e + revealed no RIA variation with the signal power (microwatts-milliwatts range), proving to be a good candidate for distributed OF sensor (DOFS) applications, while the CERTYF OF showed a clear photobleaching effect. A fitting routine based on the second-order growth kinetics model of Griscom has been performed, which has shown good consistency with the experimental results and offered a quantitative evaluation of the photobleaching effect on the CERTYF OF.
The gain degradations of an Er‐doped fiber amplifier (EDFA) during the exposure of its active Er‐doped fiber to 40 keV X‐rays (≈2.7 mrad(SiO2) s−1up to 300 krad) at three different temperatures: −40, 25, and 120 °C, are characterized. The spectral dependence of the fiber radiation‐induced attenuation (RIA) is monitored in situ in the 900–1600 nm spectral range, highlighting a combined temperature and radiation effect on the near‐infrared RIA levels and kinetics. At the system level, the kinetics of EDFA gain degradation are only slightly affected by varying the irradiation temperature for the tested backward pumping EDFA configuration. On the theoretical side, a homemade computer code based on the particle swarm optimization and the rate equations to model the radiation behavior of EDFA is used, considering only the RIA impact on its gain. Despite a good agreement between experimental and simulation results below the dose of 70 krad corresponding to current space missions, the comparison between the modeled and measured gain degradation kinetics at higher doses shows that a more precise modeling of the temperature impact on the absorption properties of the erbium ions is necessary to better reproduce the EDFA radiation behavior for future space missions.
26 March 2021 in IEEE Transactions on Nuclear Science
We investigated the coupled radiation and temperature effect on the gain degradation of Erbium Doped Fiber Amplifier (EDFA) and Erbium-Ytterbium Doped Fiber Amplifier (EYDFA). The irradiation temperatures range from -40°C to 120°C. Steady state X-ray (40 keV, 300 krad (SiO2), ~27 rad/s) experiments provide evidence for a minor coupled radiation and temperature effect on the gains of both reference and radiation-tolerant EDFA and EYDFA. This is an important result as it validates the reliance on room-temperature testing in establishing the suitability of fiber amplifiers for space applications. Furthermore, we also investigated the Radiation Induced Attenuation (RIA) kinetics during and after the various rare-earth doped fiber irradiations to improve our knowledge of the basic radiation-effects mechanisms and their dependence on the temperature during irradiation. It appears that these effects also depend on the presence of Cerium, a codopant that is incorporated to passivate the Al or P-related defects and then to enhance the amplifier radiation tolerance.
31 March 2023 in IEEE Transactions on Nuclear Science
Combined temperature and photobleaching (PB) effects on the 1550 nm radiation-induced attenuation (RIA) levels and kinetics of a commercial Ge-doped single-mode optical fiber have been investigated. The main goal of this study was to evaluate if synergetic effects could impact the performances of free space optical communication links in space. For this, we performed accelerated (0.5 Gy(SiO 2 )/s) irradiation runs with 100 kV X rays up to the total ionizing dose of 150 kGy(SiO 2 ), varying the irradiation temperature between -80 °C and 80 °C. First, we evaluate the irradiation temperature effects: infrared RIA largely increases at negative temperatures. Second, the effects of injecting different optical powers at the different temperatures have been characterized: if at temperatures exceeding room temperature (RT), PB effects are almost negligible, a PB effect is clearly observable at lower temperatures where the germanosilicate optical fiber present large RIA levels due to the contribution of metastable defects absorbing at 1550 nm. Increasing the injected powers allows reducing the concentration of these radiation-induced unstable defects, but not as much as thermal treatment consecutive to the irradiation. These results highlight the complex physics of radiation induced defects absorbing at 1550 nm in Ge-doped optical fiber, but also the vulnerability of this class of fiber for space telecommunication links. Regarding the unstable nature of point defects causing the RIA at lower temperature, it seems possible to mitigate the loss excess by thermal cycles at RT or higher temperatures. We also could expect that our accelerated tests represent a worst-case scenario in terms of RIA levels at the maximum dose.
13 January 2022 in IEEE Transactions on Nuclear Science
We investigated the X-ray radiation impact on the performances of “backup” Erbium Doped Fiber Amplifiers (EDFAs) and Erbium-Ytterbium Doped Fiber Amplifier (EYDFA). These devices are exposed to the space radiation constraints, unpowered in the “OFF” mode, up to their hypothetic activation during the mission. This atypical profile of use must be considered as it could lead to a higher radiation vulnerability. To carry this study, active optical fibers differing in terms of radiation hardness, have been exposed to steady-state X-rays under different profiles of amplifier use: the gain degradation is measured by varying the pumping conditions, that drive the photobleaching phenomenon, during the radiation exposure: “ON” (100% ON), “OFF” (0% ON), and “OFF-ON-OFF” with powering 2% or 10% of the time. Our results show that the impact of the pump and its related photobleaching efficiency depend on the selected active fiber to build the amplifier. An important result is that the “backup” EDFA designed with radiation-hardened Ce-doped fiber does not suffer from an extra-degradation due to the “OFF” mode, contrary to the one designed with a non-rad-hard fiber. For this latter one, it is indeed possible to reduce the extra-gain degradation by powering the amplifier for short time periods during the “OFF” state, otherwise the EDFA recovers this extra-gain degradation in a few hours after turning “ON” in our test conditions. For the tested radiation-tolerant EYDFA, an enhanced vulnerability is observed for the “OFF” amplifier, that can be reduced too by briefly powering the amplifier. The origins of these effects are discussed basing on the properties of point defects related to the aluminosilicate (EDFA) and phosphosilicate (EYDFA) glasses of the fiber.
21 November 2019 in IEEE Transactions on Nuclear Science
We investigated the X-ray (40 keV, 700 Gy(SiO2), ∼80 mGy/s) radiation effects on the performances (gain) of Er-Doped Fiber pre-Amplifier (EDFA) and Er/Yb codoped Fiber boost Amplifier (EYDFA). Various EDFA and EYDFA architectures have been designed to operate either in Wavelength Division Multiplexing (WDM) or Dense WDM (DWDM) schemes. We compare the performances of amplifiers based on conventional or radiation hardened versions of the active Er-doped or Er/Yb-codoped fibers. Our results show that for all amplifier architectures, the various channels undergo similar gain degradation levels and kinetics, as expected from the measured spectral dependence of the radiation-induced attenuation of the phosphosilicate (ErYb-doped) and aluminosilicate (Er-doped) glass matrix of these fibers. This degradation remains very limited for the amplifiers based on radiation hardened fibers, with gain decrease of less than 0.3 mdB.Gy-1 for the EDFA (∼30 dB initial gain) and less than 0.8 mdB.Gy-1 for the EYDFA (∼18 dB initial gain) in the DWDM architecture.