22 August 2022 in Aerospace technic and technology
The effect of temperature and air pressure at the supersonic nozzle inlet, as well as the distance from the nozzle outlet to the surface of the substrate (stand-of-distance) on the powder usage rate of nickel-based powder in low pressure cold gas-dynamic spraying (inlet pressure up to 1.0 MPa) was analyzed. One of the most important parameters characterizing the deposition efficiency of the spraying process is the powder usage rate. This parameter is the ratio of the mass of the coating to the mass of the powder used to obtain this one. For the process of cold gas-dynamic spraying, implemented on the equipment using air pressure up to 1.0 MPa, the main disadvantage is the relatively low-powder usage rate. To increase it (but not limited to it), a ceramic component, such as alumina Al2O3, is added to pure metal powders. In this study a nickel-based powder mixture, in which the content of Al2O3 powder is about 10% mass., was used. Titanium alloy plates BT9 were used as the substrate material. Based on the multifactor planning of the experiment, the effect of the complex parameters of the low-pressure cold gas-dynamic spraying on the powder usage rate was studied. After the coating deposition according to the matrix of the experiment, the samples with coatings were weighed. According to the known mass of the samples before spraying and the increase in their mass, the powder usage rate was calculated. From the analysis of the obtained statistical data, the dependence of the effect of the complex parameters of the deposition process on the powder usage rate was developed. The maximum value of the powder usage rate were obtained up to 35 %. It was confirmed that the air temperature at the nozzle inlet has the greatest effect on the above-mentioned parameter. The explanation of this is the increase in gas flow temperature and velocity, and as a result, the increase in the velocity and temperature of the powder particles in this flow. Higher values of the velocity and temperature of the particles lead to more intense plastic deformation of particles during impact with the substrate and their adhesion to it.
24 August 2023 in Aerospace technic and technology
The subject of the research is the influence of low-pressure cold spraying process parameters on the adhesive strength of the coatings. The goal is to ensure the maximum values of the adhesive strength of nickel-based coatings deposited by cold spraying by controlling the gas temperature at the nozzle inlet. The task is to investigate the effect of the temperature mode of the DYMET-405 machine on the adhesive strength of the coatings obtained from the Ni+Zn+Al2O3 powder mixture at constant other spraying parameters. Research methods. The experimental study of the adhesive strength was conducted on the tear using adhesive method in accordance with DSTU 2639-94. The metal-matrix composite powder mixture Ni+Zn+Al2O3 was used as powder material. VT3-1 titanium alloy was chosen as substrate material. Coatings were deposited using DYMET-405 low-pressure cold spraying machine. Temperature regulation at the nozzle inlet was performed by turning on the required temperature mode on the equipment control panel. Other spraying parameters remained constant during coating deposition process. The results. It was established that with an increase in the temperature of the gas in the nozzle, an increase in the adhesive strength of coatings is observed, on average from 9.5 MPa to 28.7 MPa. This can be explained by the fact that an increase in gas temperature leads to an increase in the velocity of the gas flow and, accordingly, of the powder particles in this flow. Higher particle impact velocity has a positive effect on the process of their deforming, filling of pores, densifying of coating layers, and finally increasing the adhesive and cohesive strength. The scientific novelty of the obtained results is that the dependence of the gas temperature at the nozzle inlet during low-pressure cold spraying on the adhesive strength of Ni+Zn+Al2O3 powder mixture coatings deposited on VT3-1 titanium alloy substrates was obtained. Conclusions. The practical value of the obtained results is that the obtained dependences of adhesive strength on gas temperature can be used for the development of cold spraying recommendations for the deposition of restorative coatings on parts made of titanium alloys, in particular in aircraft engines to eliminate operational defects.