9 August 2021 in IEEE Transactions on Microwave Theory and Techniques
A time-division duplex (TDD) transmit/receive (T/R) millimeter-wave (mm-wave) front-end in 0.13-μm SiGe BiCMOS for fifth generation (5G) is presented. The front-end is composed of a power amplifier (PA), a low noise amplifier (LNA), and a single-pole double-throw (SPDT) switch. At mm-wave bands, the traditional SPDT switch limits the output power of the front-end in transmit mode. In this article, an asymmetric SPDT switch is proposed with high-power-handling capability (simulated OP $_{{1,dB}} > 28$ dBm), low insertion loss, and compact structure at 24-30 GHz. A balanced architecture is used to implement a high gain and high linearity PA with excellent input/output return losses and load-variation insensitivity. The effect of the feedback capacitor in the base of the cascode stage has been analyzed. The standalone PA achieves OP $_{{1,dB}}$ /peak PAE > 16.9 dBm/18.7% across 24-30 GHz and the OP $_{{1,dB}}$ /peak PAE still exceeds >15.9 dBm/16.3% including the switch loss and compression. 5G NR FR2 64-QAM modulation tests demonstrate the high linearity of the balanced PA. At 28 GHz, the standalone PA shows the EVM of -29.93 dB/-26.06 dB with an average output power ( $P_{{avg}}$ ) of 10.15 dBm/12.16 dBm. The front-end in transmit mode shows the EVM of -29.63 dB/-26.02 dB with an average output power of 7.76 dBm/9.59 dBm. A wideband LNA is designed and exhibits a measured gain of 26 dB with a 3-dB bandwidth of 19-35 GHz, a noise figure (NF) < 5.3 dB at 24-30 GHz including the switch loss. The proposed front-end achieves high linearity in transmit mode and low NF in receive mode.
27 September 2019 in IEEE Transactions on Circuits and Systems II: Express Briefs
This paper presents a W-band 6-bit active phase shifter fabricated in 0.13 μm SiGe BiCMOS process. A wideband quadrature signal generator composed of a 90-degree hybrid and a pair of transformers is exploited for low insertion loss and superior balance. Conventional architecture used in gain control unit is replaced by a novel phase inverter-embedded variable gain amplifier to achieve a high gain and low complexity. In addition, a balun-first combiner with symmetrical layout is utilized at the output to keep as low the imbalance of I/Q paths as possible. The proposed phase shifter exhibits a record average gain of 7 dB at 79 GHz with a 3-dB bandwidth from 71.5 to 84.5 GHz. The variation of gain remains below 2.1 dB over 64 phase states. The measured RMS phase error is 1.35∘ at 78 GHz and remains below 3.5∘ from 72 to 82 GHz. The RMS gain error is measured to be 0.46 dB at 75 GHz and keeps less than 0.76 dB from 71 to 82 GHz. The measured input 1dB compression point amounts to -10 dBm. To the best of the author’s knowledge, this work presents the lowest RMS phase error (1.35∘) and the highest gain (7 dB) compared with the reported silicon-based W-band active phase shifters.
15 July 2022 in IEEE Journal of Solid-State Circuits
This article presents a pair of W-band phased-array transmitter (TX) and receiver (RX) chipsets in a 0.13- $\mu \text{m}$ SiGe BiCMOS process for high data-rate wireless communication. Both the chips integrate four compact front-end channels in 2 $\times $ 2 distribution, and the distance between the adjacent RF pads is less than 1.8 mm ( $0.56\lambda $ at 90 GHz) to fit for the tight antenna array and enable array scaling by tiling multiple unit cells. A 6-bit active phase shifter based on the improved phase-inverting variable gain amplifiers is leveraged to achieve high phase-shift precision and bandwidth concurrently. A noise reduction technique using a parallel inductor to resonate with the parasitic capacitors of the cascode transistors is adopted in the low-noise amplifier design. A novel miniature power combiner, which occupies a much more compact area than the Wilkinson power combiner while delivering great RF performance, is proposed and elaborately analyzed. System-level calibration for local oscillator (LO) leakage and dc-offset suppression is enabled by introducing digitally controlled current sources into the up-conversion and down-conversion mixers. On-wafer measurements for the TX chip exhibit a single-channel IF-to-RF conversion gain (CG) of 26 dB, a competitively high output 1-dB compression point (OP $_{\mathrm {1\,dB}}$ ) of 11 dBm. The RX chip achieves an RF-to-IF CG of 19.5 dB with 9-/14-GHz IF/RF 3-dB bandwidth, a noise figure of 7.7 dB, and an input 1-dB compression point of −28 dBm. The phase-shift characteristics are verified by the TX/RX front-end measurements, achieving a 6-bit phase resolution with minimum rms phase/gain error smaller than 0.83°/0.45 dB and a large phase-shift bandwidth higher than 20 GHz. Preliminary wireless transmission test using a low-cost die-on-printed circuit board (PCB) prototype demonstrates wireless data rates of 1.6 and 0.8 gigabits per second (Gb/s) at distances of 0.4 and 1 m with 256-quadratic-amplitude modulation (QAM) and 16-QAM modulated signals, respectively.
16 February 2021 in IEEE Microwave and Wireless Components Letters
This letter presents a multiband switchable low-noise amplifier (LNA) in the 0.1- μm GaAs pHEMT process. Employing a new varactor-based tunable network as the interstage matching circuit, the operation bands can be tuned consecutively and cover the 5G millimeter-wave frequency bands N257/N260. The proposed tunable structure functions well without sacrificing noise performance or increasing dc consumption and chip area. In the entire operation band from 26.5 to 41 GHz, the LNA achieves a small-signal gain of over 24 dB and a noise figure (NF) of less than 2.9 dB. The measured result shows a small-signal gain of 25.1 dB/27.7 dB and an NF of 2.4 dB/2.8 dB at 28 GHz/39 GHz. The measured input 1-dB compression point (IP 1dB ) is -18.3 dBm/-17 dBm at 28 GHz/39 GHz. The measured input-referred intercept point (IIP 3 ) is -8.8 dBm/-8.5 dBm at 28 GHz/39 GHz. The LNA has a chip size of 1.6 mm ×1 mm, and the total power consumption is 74 mW. To the best of our knowledge, the proposed LNA is the state-of-the-art Ka-band switchable LNA and has similar performance compared with single-band LNAs using the same technology.
24 January 2023 in IEEE Journal of Solid-State Circuits
This article presents a fully integrated 220 GHz sliding-intermediate frequency (sliding-IF) quadrature transmitter (Tx) and receiver (Rx) chipset supporting high-order modulation schemes in a 0.13- $\mu$ m SiGe bipolar junction transistor and the complementary metal-oxide-semiconductor transistor (BiCMOS) technology with $f_{T}$ / $f_{\mathrm{max}}$ $=$ 300/500 GHz. For supporting the sliding-IF scheme, a 55-GHz frequency tripler, a low-loss miniature power splitter, and a 165-GHz high-efficiency frequency tripler are employed for the local oscillator (LO) generator of the transceiver (TRx). By using the sliding-IF architecture, the power consumption of the LO generator in the sub-terahertz (sub-THz) band is effectively reduced. The proposed miniature power splitter occupies a small area, which is flexible for Tx and Rx layout arrangements. In the Tx part, a 220-GHz high-gain, high-linearity power amplifier (PA) is employed to enhance the conversion gain (CG) and output power of the Tx. Two up-conversion mixers are introduced for double conversion in sliding-IF architecture. The Tx exhibits 42-GHz RF bandwidth, 38-dB CG, and 8.5-dBm saturated output power ( $P_{\mathrm{sat}}$ ). On the Rx side, a 220-GHz low noise amplifier (LNA) with a noise-reduction technique is employed to reduce the noise figure (NF) of the Rx. A double-conversion Gilbert-like topology is proposed for the down-conversion mixer which saves power consumption and reduces the NF. A baseband amplifier (BBA) follows the down-conversion mixer to improve the dynamic range. The Rx exhibits 31-GHz RF bandwidth, 48-dB CG with 25-dB gain control, and 11-dB single sideband (SSB) NF. Furthermore, on-chip slot antennas are adopted in the Tx and Rx to reduce the losses introduced by the interconnection between off-chip antennas and RF front-end devices. The antenna combined with a 20-mm radius silicon lens provides high directivity. Wireless transmission experiments demonstrate 11.2/2.4 Gbps data rates with 16-QAM/64-QAM modulation scheme over 0.2 m. The Tx and Rx consume around 640 and 495 mW, respectively.
25 August 2020 in IEEE Transactions on Terahertz Science and Technology
This article presents a 250-GHz SiGe amplifier composed of three differential cascode stages in a 0.13-μm SiGe BiCMOS technology (f T /f MAX = 300/500 GHz). The Marchand balun is utilized to implement single-ended to differential signal transformation for its superior performance over the transformer-based balun at sub-THz frequencies, which has been investigated and verified through electromagnetic (EM) simulations. A stair-like interconnection method and conventional positive feedback technique are used to improve the inherent gain of the active device. The proposed amplifier exhibits a record S 21 of 21.5 dB at 252 GHz and a 3-dB bandwidth of 11 GHz with the capability of gain control. The measured OP 1dB is -3.7 dBm with the corresponding power added efficiency (PAE) of 0.3%, and the saturated output power is estimated to exceed 0 dBm at 252 GHz. The overall power consumption of the chip is 149 mW. Along with remarkable gain and output power, the compact amplifier is suitable to be adopted as an output block in the sub-THz transmitters.