3 July 2020 in IEEE Transactions on Microwave Theory and Techniques
A D-band waveguide diplexer, implemented by silicon micromachining using releasable filling structure (RFS) technique to obtain high-precision geometries, is presented here for the first time. Prototype devices using this RFS technique are compared with devices using the conventional microfabrication process. The RFS technique allows etching large waveguide structures with nearly 90° sidewall angles for the 400-μm-tall waveguides. The diplexer consists of two direct-coupled cavity six-pole bandpass filters, with the lower and the upper band at 130-134 and 141-148.5 GHz, respectively. The measured insertion loss of the two bands is 1.2 and 0.8 dB, respectively, and the measured return loss is 20 and 18 dB, respectively, across 85% of the passbands. The worst case adjacent channel rejection is better than 59 dB. The unloaded quality factors of a single cavity resonator are estimated from the measurements to reach 1400. Furthermore, for the RFS-based micromachined diplexer, an excellent agreement between measured and simulated data was observed, with a center frequency shift of only 0.8% and a bandwidth deviation of only 8%. In contrast to that, for the conventionally micromachined diplexer of this high complexity, the filter poles are not well controllable, resulting in a large center frequency shift of 3.5%, a huge bandwidth expanding of over 60%, a poor return loss of 6 and 10 dB for the lower and the upper band, respectively, and an adjacent channel rejection of only 22 dB.
10 May 2021 in IEEE Transactions on Microwave Theory and Techniques
In this work, we propose a new concept of phase shifting by tuning the coupling distance between two parallel silicon slabs that support the propagation of an in-phase supermode. A prototype device was implemented in the 220–330-GHz band by integrating the micro-electro-mechanical system (MEMS)-actuated phase-shifting mechanism, based on two moveable parallel-coupled high-resistivity silicon slabs, inside a metallized hollow rectangular waveguide in silicon-on-insulator (SOI) micromachining technology. The prototype device has been characterized to a maximum continuous phase tunability of 550° with a maximum insertion loss of 1.87 dB achieved at 330 GHz. A maximum figure-of-merit (FOM) of 375°/dB is achieved at around 320 GHz, which presently is the highest FOM value reported for any phase shifter in the subterahertz (sub-THz) frequency range. The bandwidth covers the whole waveguide band with an average and worst case insertion loss of 1.94 and 2.5 dB, respectively, a worst case insertion-loss variation of 0.7 dB and a phase error better than 4° for all phase states. A large displacement of MEMS electrostatic comb-drive actuators that are co-fabricated in the micromachined waveguide platform is achieved by a driving voltage of 50 V. The prototype footprint is $7.3 \times 5.3$ mm 2 .
7 January 2022 in IEEE Transactions on Microwave Theory and Techniques
This article presents a new, very compact silicon-micromachined two-port waveguide platform that features axial ports but allows to integrate waveguide devices, which is enabled by integrated broadband, back-to-back, stepped E- and H-plane bends. This approach of rotating the waveguide plane in two axes enables devices of complex geometry to be directly mounted between two waveguide flanges. A prototype transition operating at 220–320 GHz has experimentally demonstrated an insertion loss of less than 0.2 dB and a return loss of better than 18.5 dB throughout the entire WM-864 waveguide band, characterized by an integrated on-chip waveguide calibration kit. Two 5th-order waveguide filters have been designed as complex demonstrator devices and co-fabricated with the proposed axial integration platform, demonstrating a direct-coupled filter at 270 GHz and a cross-coupled filter at 300 GHz with three transmission zeros. The filters with 1.85% and 2% fractional bandwidths demonstrate a measured insertion loss of 1.92 and 1.50 dB, respectively, to which the two transitions combined add a total of 0.3 dB, and a return loss of 19 and 15 dB in the passbands, respectively. The unloaded $Q$ -factors for the resonator cavities of the two filters were extracted to 750 and 900, respectively. These results are so far unparalleled for filters of similar complexity in this frequency range. The sensitivity to fabrication tolerances is analyzed.
8 March 2024 in Journal of Micromechanics and Microengineering
This paper presents a wafer-scale silicon microfabrication technology for the sub-terahertz (sub-THz) waveguide device mass production. Based on the effective scheme, a WR-5 (140–220 GHz) straight rectangular waveguide and a WR-2.8 (260–400 GHz) rectangular waveguide bandpass filter are implemented as demonstrated examples. The silicon deep reactive ion etching (DRIE) process is employed to etch through the total thickness of the silicon wafer and form the main waveguide channels. Then, a low-temperature thermal compression process is used to bond the trough-etched wafer with the top and bottom metallised silicon wafers to form the closed waveguide structures without any precise alignment process. The fabricated waveguide has the benefit of low transmission loss (0.03–0.05 dB mm−1) at the whole G band. Besides, to measure the fabricated WR-2.8 waveguide filter and solve the measuring equipment standard waveguide difference, silicon micromachined waveguide transitions are explored and fabricated to match two different frequency-band modules for measuring the waveguide filters in the desired full frequency band, which also has a potential application for the different size waveguide conversion. The measured results agree well with the simulated ones. The measured 3 dB bandwidth is 9.3%, with a central frequency of 343 GHz; the average insertion loss (IL) is about 1.6 dB in the pass band, including two extra straight waveguides of 8 mm length on input/output ends and two external waveguide-to-waveguide transitions. The proposed method provides a feasible and cost-effective solution for the mass production of high-performance waveguide devices and integrated systems in sub-THz frequency bands and beyond.
9 April 2021 in Journal of Microelectromechanical Systems
This letter presents an under-etching prevention method for an aqueous hydrofluoric acid (HF) releasing process by adding a single-side low-pressure chemical vapor deposition (LPCVD) silicon protection layer. The proposed method enables advanced silicon-on-insulator (SOI) based millimeter-wave/terahertz (mmW/THz) MEMS waveguide devices, which require for RF performance a complete metallization film over the SOI buried-oxide (BOX) layer, and simultaneously need a locally under-etched BOX layer for implementing MEMS actuators reconfiguring the devices. A comparison between the WR-3.4 waveguide (220-330 GHz) using the proposed under-etching prevention method and the one without using it proves the effectiveness and feasibility during HF releasing processes. A MEMS tunable phase shifter driven by comb-drive actuators has been successfully implemented by applying this method in a micromachined waveguide. [2021-0036]
6 December 2025 in Applied Surface Science