Division of Micro and Nanosystems, School of Electrical Engineering and Computer Science, KTH Royal Institute of Technology, Stockholm SE-100 44, Sweden
Auto-generated profile, based on publicly available information
Adrian Gomez-Torrent
Division of Micro and Nanosystems, School of Electrical Engineering and Computer Science, KTH Royal Institute of Technology, Stockholm SE-100 44, Sweden
A very low-profile sub-THz high-gain frequency beam steering antenna, enabled by silicon micromachining, is reported for the first time in this paper. The operation bandwidth of the antenna spans from 220 to 300 providing a simulated field of view of 56°. The design is based on a dielectric filled parallel-plate waveguide (PPW) leaky-wave antenna fed by a pillbox. The pillbox, a two-level PPW structure, has an integrated parabolic reflector to generate a planar wave front. The device is enabled by two extreme aspect ratio, 16 x 16 large perforated membranes, which are only 30 thick, that provide the coupling between the two PPWs and form the LWA. The micromachined low-loss PPW structure results in a measured average radiation efficiency of –1 and a maximum gain of 28.5dBi with an input reflection coefficient below –10. The overall frequency beam steering frontend is extremely compact (24 × 24 × 0.9) and can be directly mounted on a standard WM-864 waveguide flange. The design and fabrication challenges of such high performance antenna in the sub-THz frequency range are described and the measurement results of two fabricated prototypes are reported and discussed.
10 February 2020 in IEEE Transactions on Antennas and Propagation
Two high-gain flat array antenna designs operating in the 320 – 400 GHz frequency range are reported in this paper. The two antennas show measured gains of 32.8 dBi and 38 dBi and consist of a 16 × 16 (256) element array and a 32 × 32 (1024) element array, respectively, which are fed by a corporate H-tree beamforming network. The measured operation bandwidth for both antennas is 80 GHz (22% fractional bandwidth), and the total measured efficiency is above -2.5 dB and above -3.5 dB for the two designs in the whole bandwidth. The low measured loss and large bandwidth are enabled by optimizing the designs to the process requirements of the SOI micromachining technology used in this work. The total height of the antennas is 1.1mm (1.2 λ at the center frequency), with sizes of 15mm × 18mm and 27mm × 30mm for both arrays. The antennas are designed to be directly mounted onto a standard WM-570 waveguide flange. The design, fabrication, and measurements of eight prototypes are discussed in this paper and the performance of the antennas compared to the simulated data, as well as manufacturability and fabrication repeatability are reported in detail.
21 November 2018 in IEEE Transactions on Terahertz Science and Technology
This paper reports on a turnstile-junction orthomode transducer (OMT) implemented by silicon micromachining in the 220-330-GHz band. Turnstile OMTs are very wideband and allow for co-planar ports but require accurate and complex geometries, which makes their fabrication challenging at higher frequencies. The compact 10 mm x 10 mm x 0.9 mm OMT-chip presented in this paper is the first micromachined full-band OMT in any frequency range and only the second turnstile OMT implemented above 110 GHz. The measured insertion loss (0.3 dB average, 0.6 dB worst case) and the cross polarization (60 dB average, 30 dB worst case) over the whole waveguide band represent the best performance of any wideband OMT, regardless of design or fabrication technology, in the 220-330-GHz band. The return loss with 22 dB average (16 dB worst case) is comparable with or better than previous works. This paper discusses design considerations and compromises of this complex 9-layer silicon micromachined device, including the influence of side-wall slopes, underetching, and postbonding misalignment between the chips. It is shown that for a device that is very sensitive to geometrical variations, such as a turnstile OMT, it is necessary to anticipate and compensate for any fabrication imperfections in the design to achieve high RF performance.
3 July 2020 in IEEE Transactions on Microwave Theory and Techniques
A D-band waveguide diplexer, implemented by silicon micromachining using releasable filling structure (RFS) technique to obtain high-precision geometries, is presented here for the first time. Prototype devices using this RFS technique are compared with devices using the conventional microfabrication process. The RFS technique allows etching large waveguide structures with nearly 90° sidewall angles for the 400-μm-tall waveguides. The diplexer consists of two direct-coupled cavity six-pole bandpass filters, with the lower and the upper band at 130-134 and 141-148.5 GHz, respectively. The measured insertion loss of the two bands is 1.2 and 0.8 dB, respectively, and the measured return loss is 20 and 18 dB, respectively, across 85% of the passbands. The worst case adjacent channel rejection is better than 59 dB. The unloaded quality factors of a single cavity resonator are estimated from the measurements to reach 1400. Furthermore, for the RFS-based micromachined diplexer, an excellent agreement between measured and simulated data was observed, with a center frequency shift of only 0.8% and a bandwidth deviation of only 8%. In contrast to that, for the conventionally micromachined diplexer of this high complexity, the filter poles are not well controllable, resulting in a large center frequency shift of 3.5%, a huge bandwidth expanding of over 60%, a poor return loss of 6 and 10 dB for the lower and the upper band, respectively, and an adjacent channel rejection of only 22 dB.
25 September 2019 in IEEE Transactions on Terahertz Science and Technology
A new integration concept for THz systems is presented, wherein patterned silicon-on-insulator wafers form all DC, IF and RF networks in a homogeneous medium, in contrast to existing solutions. Using this concept, silicon-micromachined waveguides are combined with silicon germanium (SiGe) microwave monolithic integrated circuits (MMICs) for the first time. All features of the integration platform lie in the waveguide's H-plane. Heterogeneous integration of SiGe chips is achieved using a novel in-line H-plane transition. As an initial step towards complete systems, we outline the design, fabrication and assembly of back-to-back transition structures, for use at D-band frequencies (110 – 170 GHz). Special focus is given to the industrial compatibility of all components, fabrication and assembly processes, with an eye on the future commercialisation of THz systems. Prototype devices are assembled via two distinct processes, one of which utilises semi-automated die-bonding tools. Positional and orientation tolerances for each process are quantified. An accuracy of ±3.5 μm, ±1.5 ° is achieved. Measured S-parameters for each device are presented. The insertion loss of a single-ended transition, largely due to MMIC substrate losses, is 4.2 – 5.5 dB, with a bandwidth of 25 GHz (135 – 160 GHz). Return loss is in excess of 5 dB. Measurements confirm the excellent repeatability of the fabrication and assembly processes and thus their suitability for use in high-volume applications. The proposed integration concept is highly scalable, permitting its usage far into the THz frequency spectrum. This work represents the first stage in the shift to highly-compact, low-cost, volume-manufacturable THz waveguide systems.
20 July 2016 in IEEE Transactions on Microwave Theory and Techniques
A novel chirping technique is applied to the design of very high-power waveguide harmonic low-pass filters. The technique could be used, for instance, to avoid multipactor testing in multicarrier systems such as the output multiplexer of a communications satellite. The novel chirped filter shows low insertion loss, all higher order mode suppression, and broad stopband rejection up to the third harmonic. This paper focuses on the maximization of the filter power-handling capability without affecting its excellent frequency behavior. Given a certain frequency response, the E-plane mechanical gap of the structure and the length (in the propagation direction) of the waveguide sections between its constituent bandstop elements can be considered to improve the high-power behavior. However, the power performance may not be sufficient yet in some applications if we wish, for instance, multipactor testing to be avoided. This becomes feasible by chirping the length (in the propagation direction) of the bandstop elements. An example for Ku band is discussed for relevant frequency specifications. An improvement from $\sim 8$ kW (non-chirped filter) to more than 100 kW (chirped filter) is obtained. As a reference, the equivalent waffle-iron filter can handle only 0.15 kW. Such high-power threshold levels have never been reported before for such kind of filters.