5 November 2018 in Journal of Thermal Science and Engineering Applications
Fabric drying is an energy-intensive process, which generally involves blowing hot dry air across tumbling wet fabric to facilitate evaporation and moisture removal. Most of the energy supplied is used to overcome the enthalpy of vaporization for water. Although this process tends to be inefficient, it is fairly simple and forms the basis for the majority of existing clothes dryer technology today. To address the relatively low efficiency, a new method of drying called “direct contact ultrasonic fabric drying” is proposed. The process involves using high-frequency vibration introduced by piezoelectric transducers, which are in contact with wet fabric. The vibration is used to extract water droplets from the fabric mechanically. In this study, a total of 24 individual transducers are used in a module to dry a 142 cm2 sized fabric. The performance characterization of this single module has enabled successful scale-up of the system to a midscale prototype dryer, which can be used to ultrasonically dry clothing-sized fabric (∼750 cm2). The first-generation ultrasonic fabric dryer fabricated uses as little as 17% of the energy needed by traditional evaporation-based drying techniques. In addition to experimental data, this paper presents the results of a kinetic and scaling analysis that provides some important insights into ultrasonic drying.
28 June 2022 in Nuclear Technology
Dry cask storage is one of two storage methods approved by the U.S. Nuclear Regulatory Commission for spent fuel after removal from reactor cores. Dry casks consist of a stainless steel canister enclosed in a concrete overpack to contain the hazardous radioactive spent fuel rods and provide radiation shielding. Monitoring spent fuel storage casks is desired to ensure the safe containment of the enclosed spent fuel, but is very difficult due to the related harsh temperature and radiation environment. The sensors and associated electronics to monitor temperature, pressure, and/or radiation need to survive high temperatures and radiation doses for extended time periods. For this reason, there is a severe need for radiation-hardened electrical systems that survive well beyond the existing capabilities of commercially available radiation-rated electronic components, which have primarily been developed for space applications. Junction-gate field-effect transistor (JFET) devices are inherently radiation hardened [exceeding 100 Mrad (Si)]. When JFETs are used as building blocks for sensing and communication electronics (i.e., oscillators, amplifiers, filters, and mixers), inherently radiation-hardened circuits can be achieved. To this end, JFET-based radiation-hardened electronics interfacing with cask-embedded sensors capable of driving modulated sensor signals through a stainless steel barrier were designed and tested at a dose rate of approximately 500 krad/h (Si) to beyond a 200-Mrad (Si) total ionizing dose. After 200 Mrad (Si), the sensor and communication circuit signals were correctly decoded at the receiver despite oscillator drift. The results from this experiment demonstrate the potential for creating more complex radiation-hardened JFET-based electrical systems for nuclear environments.
11 October 2022 in IEEE Transactions on Device and Materials Reliability
Here, recent work to evaluate the prospects for surface acoustic wave (SAW) devices fabricated on bulk aluminum nitride (AlN) for elevated temperature and radiation environments is reported and discussed. The design and fabrication of an array of SAW devices using commercial wafers is described, including the non-standard fabrication approach taken to overcome the stress-induced warpage of the 50 mm diameter AlN substrates. Radio frequency performance characterization of the SAW devices, with resonance frequencies ranging from 0.5 GHz to 1.5 GHz, is described. The linear temperature coefficient of frequency (TCF) near room temperature was measured and is compared to theoretical results from other investigators. The effects of 8 MeV Al ion irradiation at 300∘C and 500∘C to damage levels of 0.01, 0.1 and 1 displacements per atom (dpa), as a proxy for neutron irradiation, was investigated. The ion irradiation damage was observed to decrease the SAW resonant frequency, and this effect is characterized and discussed. Significant degradation in the conductivity of the Ti/Al electrodes of the SAW devices was also observed and characterized. These experimental results provide a basis for further investigation of the prospects for development of SAW sensor devices in bulk AlN material for application in elevated temperature and radiation environments.