Saeed Moghaddam

Prof. Saeed Moghaddam


Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2014 in Journal of Membrane Science
Verified
Journal Article
Closed access
APAbhilash Paneri
Abhilash Paneri
YHYunseon Heo
Yunseon Heo
GEGregory Ehlert
Gregory Ehlert
ACAnton Cottrill
Anton Cottrill
HSHenry Sodano
Henry Sodano
SMSaeed Moghaddam
Saeed Moghaddam

17 March 2017 in Scientific Reports
Verified
Journal Article
Open access
PDF file
SBSajjad Bigham
Sajjad Bigham
AFAbdolreza Fazeli
Abdolreza Fazeli
SMSaeed Moghaddam
Saeed Moghaddam
Performance enhancement of the two-phase flow boiling heat transfer process in microchannels through implementation of surface micro- and nanostructures has gained substantial interest in recent years. However, the reported results range widely from a decline to improvements in performance depending on the test conditions and fluid properties, without a consensus on the physical mechanisms responsible for the observed behavior. This gap in knowledge stems from a lack of understanding of the physics of surface structures interactions with microscale heat and mass transfer events involved in the microchannel flow boiling process. Here, using a novel measurement technique, the heat and mass transfer process is analyzed within surface structures with unprecedented detail. The local heat flux and dryout time scale are measured as the liquid wicks through surface structures and evaporates. The physics governing heat transfer enhancement on textured surfaces is explained by a deterministic model that involves three key parameters: the drying time scale of the liquid film wicking into the surface structures (τd), the heating length scale of the liquid film (δH) and the area fraction of the evaporating liquid film (Ar). It is shown that the model accurately predicts the optimum spacing between surface structures (i.e. pillars fabricated on the microchannel wall) in boiling of two fluids FC-72 and water with fundamentally different wicking characteristics.

10 July 2020 in Nanotechnology
Verified
Journal Article
Closed access
PDF file
ASAniruddh Shekhawat
Aniruddh Shekhawat
GWGlen Walters
Glen Walters
NYNing Yang
Ning Yang
JGJing Guo
Jing Guo
TNToshikazu Nishida
Toshikazu Nishida
SMSaeed Moghaddam
Saeed Moghaddam
Ferroelectric random-access memories based on conventional perovskite materials are non-volatile but suffer from lack of CMOS compatibility, scalability limitation, and a destructive reading scheme. On the other hand, ferroelectric tunnel junctions based on CMOS compatible hafnium oxide are a promising candidate for future non-volatile memory technology due to their simple structure, scalability, low power consumption, high operation speed, and non-destructive read-out operation. Herein, we report an efficient strategy based on the interface-engineering approach to improve upon the tunneling electroresistance effect and data retention by depositing bilayer oxide heterostructure (Al 2 O 3 /Hf 0.5 Zr 0.5 O 2 ) using atomic layer deposition (ALD) on Ge substrate which is treated in-situ ALD chamber with H 2 -plasma before film deposition. Integrating a thin ferroelectric layer i.e. Hf 0.5 Zr 0.5 O 2 (8.4 nm) with a thin interface layer i.e. Al 2 O 3 (1 nm) allowed us to reduce the operation (read and write) voltage to 1.4 V, and 4.3 V, respectively, while maintaining a good tunneling electroresistance or ON/OFF ratio above 10. Furthermore, an extrapolation to 1000 years at room temperature gives a residual ON/OFF ratio of 4.

12 July 2017 in Scientific Reports
Verified
Journal Article
Open access
PDF file
AFAbdolreza Fazeli
Abdolreza Fazeli
SMSaeed Moghaddam
Saeed Moghaddam
Nearly a century of research on enhancing critical heat flux (CHF) has focused on altering the boiling surface properties such as its nucleation site density, wettability, wickability and heat transfer area. But, a mechanism to manipulate dynamics of the vapor and liquid interactions above the boiling surface as a means of enhancing CHF has not been proposed. Here, a new approach is implemented to limit the vapor phase lateral expansion over the heat transfer surface and actively control the surface wetted area fraction, known to decline monotonically with increasing heat flux. This new degree of freedom has enabled reaching unprecedented CHF levels and revealed new details about the physics of CHF. The impact of wickability, effective heat transfer area, and liquid pressure on CHF is precisely quantified. Test results show that, when rewetting is facilitated, the CHF increases linearly with the effective surface heat transfer area. A maximum CHF of 1.8 kW/cm2 was achieved on a copper structure with the highest surface area among all tested surfaces. A model developed based on the experimental data suggests that the thermal conductivity of the surface structures ultimately limits the CHF; and a maximum CHF of 7–8 kW/cm2 may be achieved using diamond surface structures.

16 November 2015 in Langmuir
Verified
Journal Article
Closed access
SRSaitej Ravi
Saitej Ravi
RDRamanathan Dharmarajan
Ramanathan Dharmarajan
SMSaeed Moghaddam
Saeed Moghaddam

21 January 2020 in Applied Physics Letters
Verified
Journal Article
Open access
PDF file
GWGlen Walters
Glen Walters
ASAniruddh Shekhawat
Aniruddh Shekhawat
SMSaeed Moghaddam
Saeed Moghaddam
JJJacob L. Jones
Jacob L. Jones
Toshikazu NishidaToshikazu Nishida
Toshikazu Nishida
The emerging field of ferroelectric hafnium zirconium oxide has garnered increased attention recently for its wide array of applications from nonvolatile memory and transistor devices to nanoelectromechanical transducers. Atomic layer deposition is one of the preferred techniques for the fabrication of hafnium zirconium oxide thin films, with a standard choice of oxidizer being either O3 or H2O. In this study, we explore various oxidizing conditions and report on the in situ treatment of hydrogen plasma after every atomic layer during the deposition of hafnium zirconium oxide to increase the virgin state polarization. Three different oxidization methods were utilized during the fabrication of the Hf0.5Zr0.5O2 films: H2O, O2 plasma, and O2 plasma followed by H2 plasma. The 10 and 8 nm thick films oxidized with only O2 plasma result in initially anti-ferroelectric films. Comparatively, the addition of H2 plasma after every O2 plasma step results in films with strong ferroelectric behavior. Peak shifting of the GIXRD pattern suggests that the sequential O2-H2 plasma films tend more to the orthorhombic phase as compared to the O2 plasma and H2O oxidized films.