In three-phase ac/dc power applications, the dc-link voltage of the Vienna rectifier can function as a dual-output independent voltage source. This enables it to fulfill various output voltage requirements for dual-loaded dc-link buses. These requirements may arise owing to different charging rates applied to the dual loads or other factors that cause unbalanced voltage at the output capacitor terminals. To address these scenarios, this article introduces a novel voltage judgment component injection scheme (VJCIS) for Vienna rectifiers. The VJCIS considers the effective reduction of input current distortion and neutral point voltage oscillation in both balanced and unbalanced capacitor voltages. These improvements enhance the dc output performance, allowing the simultaneous control of balanced and unbalanced output voltages to satisfy the requirements of dual-port and parallel charging applications. The proposed VJCIS method only requires the identification of specific continuous intervals and clamping intervals using the input voltage signal and reference voltage to enhance the dc output voltage performance and eliminate zero crossing distortion in the input current. Experimental results in the practical implementation of a 2.4-kW Vienna rectifier confirm the effectiveness and correctness of the proposed method.
22 November 2024 in IEEE Transactions on Power Electronics
In the utilization of three-phase power, the DC-link voltage of the Vienna rectifier can function as two separate voltage sources, accommodating the need for varied output voltages. The voltage-oriented control is usually used to achieve proportional adjustment of the output capacitor voltage, but this typically requires an increased number of sensors. Therefore, this paper proposes a current-sensorless control for a three-phase Vienna rectifier. To reduce circuit volume and cost, the Vienna rectifier topology is analyzed, and a current-sensorless control structure is implemented to minimize circuit volume and cost. Considering the limitation of the single voltage loop in the current-sensorless structure, which affects the output transient response, this paper also proposes a feedforward control architecture. By predicting the steady-state condition of the Vienna circuit in advance, error tracking compensation is performed to improve voltage transient response and compensate for the non-ideal power semiconductor devices. Additionally, integrating the zero-sequence compensation to achieve mitigation of zero-crossing distortion of the input current in power factor correction as well as active balanced and unbalanced output voltage. Finally, through the experimental results of a 2.4 kW Vienna converter, the effectiveness and correctness of the proposed method are validated.
10 March 2025 in IEEE Open Journal of the Industrial Electronics Society
In a three-phase three-level AC/DC converter, the T-type rectifier features high efficiency and lower power switch stress, and it allows the DC-side voltage to serve as two independent output voltage sources. In practical applications, the operation of the T-type rectifier under unbalanced three-phase grid conditions must be considered. This paper establishes an improved direct power control structure based on extended power theory under unbalanced grid conditions to achieve distortion-free current for the T-type rectifier. Additionally, a feedforward virtual capacitor power compensation (FVCPC) is created to eliminate the output voltage ripples caused by the ripple power of the rectifier inductance under the unbalanced three-phase grid. The controller design of the improved direct power control and the choice of the virtual capacitor are analyzed. Furthermore, the proposed method regulates the neutral point voltage of the T-type rectifier, eliminates neutral point current disturbances, and provides a stable and accurate DC output voltage, ensuring high quality power supply. The proposed strategy does not require a phase-locked loop or AC-side system parameters, resulting in excellent dynamic performance and robustness against parameter mismatches. Finally, the effectiveness and feasibility of the proposed control strategy are verified through simulation results and the implementation of a 2.4 kW three-phase T-type rectifier.
2 December 2025 in IEEE Transactions on Power Electronics
In Vienna rectifiers, the uncontrolled diodes force commutation based on current polarity, causing a phase shift between the reference signal and input current. This results in a deviation in voltage space vector synthesis and causes current distortion during the zero-crossing interval. However, when the dc-link voltage becomes actively unbalanced in operation, the nonsynthetic region in the vector space expands, resulting in increased neutral-point current disturbances and larger neutral-point voltage oscillations. Moreover, when unbalanced grid is considered, the phase shift of the input current further aggravates the zero-crossing distortion. In addition, the unbalanced grid also introduces a second-order ripple in the output voltage. Therefore, this paper proposes nonunity power factor current optimization (NUPF-CO) strategy that simultaneously considers both unbalanced dc-link voltage and unbalanced input grid, and integrates a virtual capacitor to reduce zero-crossing distortion and compensate second-order output voltage ripple. Compared with conventional methods, the proposed NUPF-CO method can effectively mitigate current zero-crossing distortion as well as the output voltage ripple, and compensate for the nonsynthetic region as well as improve the voltage utilization of the Vienna rectifier. Finally, a 2.5-kW three-phase Vienna rectifier prototype was built to verify the feasibility and effectiveness of the proposed control strategy.
2 January 2026 in IEEE Transactions on Industrial Electronics
The suppression of current zero-crossing distortion and dc-link voltage oscillations has been a key research focus for three-phase Vienna rectifiers in recent years. In addition, under variable power factor (PF) operation, the phase difference between the input current and grid voltage increases the likelihood of the Vienna rectifier entering a nonsynthetic interval at a high modulation index. This prevents the effective synthesis of the reference voltage vector, leading to severe current distortion and voltage oscillations. In order to reduce the impact of the nonsynthetic interval on the three-phase Vienna rectifier, this article proposes a nonunity power factor current optimization (NUPF-CO) strategy to effectively reduce the negative impact of the nonsynthetic interval on system performance. This strategy allows the three-phase Vienna rectifier to avoid current zero-crossing distortion, even under variable power factor operation and actively unbalanced output voltage, while ensuring good neutral point current disturbance suppression and improving voltage utilization. Finally, a 2.5 kW three-phase Vienna rectifier is constructed for verification. The performance of the proposed NUPF-CO strategy under variable power factor conditions is compared with that of conventional strategies.
1 January 2026 in IEEE Transactions on Industrial Electronics