Yi-Hung Liao

Prof. Yi-Hung Liao

orcid

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 January 2021 in Energies
Verified
Journal Article
Open access
PDF file
FLFaa-Jeng Lin
Faa-Jeng Lin
YLYi-Hung Liao
Yi-Hung Liao
JLJyun-Ru Lin
Jyun-Ru Lin
WLWei-Ting Lin
Wei-Ting Lin
An interior permanent magnet synchronous motor (IPMSM) drive system with machine learning-based maximum torque per ampere (MTPA) as well as flux-weakening (FW) control was developed and is presented in this study. Since the control performance of IPMSM varies significantly due to the temperature variation and magnetic saturation, a machine learning-based MTPA control using a Petri probabilistic fuzzy neural network with an asymmetric membership function (PPFNN-AMF) was developed. First, the d-axis current command, which can achieve the MTPA control of the IPMSM, is derived. Then, the difference value of the dq-axis inductance of the IPMSM is obtained by the PPFNN-AMF and substituted into the d-axis current command of the MTPA to alleviate the saturation effect in the constant torque region. Moreover, a voltage control loop, which can limit the inverter output voltage to the maximum output voltage of the inverter at high-speed, is designed for the FW control in the constant power region. In addition, an adaptive complementary sliding mode (ACSM) speed controller is developed to improve the transient response of the speed control. Finally, some experimental results are given to demonstrate the validity of the proposed high-performance control strategies.

14 March 2024 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
YLYi-Hung Liao
Yi-Hung Liao
BXBing-Rong Xie
Bing-Rong Xie
JLJia-Sheng Liu
Jia-Sheng Liu
In three-phase ac/dc power applications, the dc-link voltage of the Vienna rectifier can function as a dual-output independent voltage source. This enables it to fulfill various output voltage requirements for dual-loaded dc-link buses. These requirements may arise owing to different charging rates applied to the dual loads or other factors that cause unbalanced voltage at the output capacitor terminals. To address these scenarios, this article introduces a novel voltage judgment component injection scheme (VJCIS) for Vienna rectifiers. The VJCIS considers the effective reduction of input current distortion and neutral point voltage oscillation in both balanced and unbalanced capacitor voltages. These improvements enhance the dc output performance, allowing the simultaneous control of balanced and unbalanced output voltages to satisfy the requirements of dual-port and parallel charging applications. The proposed VJCIS method only requires the identification of specific continuous intervals and clamping intervals using the input voltage signal and reference voltage to enhance the dc output voltage performance and eliminate zero crossing distortion in the input current. Experimental results in the practical implementation of a 2.4-kW Vienna rectifier confirm the effectiveness and correctness of the proposed method.

22 November 2024 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
YLYi-Hung Liao
Yi-Hung Liao
BXBing-Rong Xie
Bing-Rong Xie
JLJia-Sheng Liu
Jia-Sheng Liu
In the utilization of three-phase power, the DC-link voltage of the Vienna rectifier can function as two separate voltage sources, accommodating the need for varied output voltages. The voltage-oriented control is usually used to achieve proportional adjustment of the output capacitor voltage, but this typically requires an increased number of sensors. Therefore, this paper proposes a current-sensorless control for a three-phase Vienna rectifier. To reduce circuit volume and cost, the Vienna rectifier topology is analyzed, and a current-sensorless control structure is implemented to minimize circuit volume and cost. Considering the limitation of the single voltage loop in the current-sensorless structure, which affects the output transient response, this paper also proposes a feedforward control architecture. By predicting the steady-state condition of the Vienna circuit in advance, error tracking compensation is performed to improve voltage transient response and compensate for the non-ideal power semiconductor devices. Additionally, integrating the zero-sequence compensation to achieve mitigation of zero-crossing distortion of the input current in power factor correction as well as active balanced and unbalanced output voltage. Finally, through the experimental results of a 2.4 kW Vienna converter, the effectiveness and correctness of the proposed method are validated.

20 February 2025 in IEEE Access
Verified
Journal Article
Open access
YLYi-Hung Liao
Yi-Hung Liao
WLWei-Rong Lai
Wei-Rong Lai
MYMeng-Hsuan Yu
Meng-Hsuan Yu
TLTing-Hsien Lin
Ting-Hsien Lin
This study proposes a power regulation strategy for a bidirectional interlinking converter (BIC) in a hybrid AC/DC microgrid. The proposed control strategy utilizes grid forming virtual synchronous generator (VSG) control of BIC to achieve global power sharing (GPS) between two sub-grids, AC and DC sub-grids, in islanded mode. Both grid-connected mode and islanded mode are incorporated in the system. This approach allows BIC to operate under a voltage source fault in the AC subgrid. The control strategy includes both communication-based and communication-less approaches to handle communication equipment failures. In the DC-side, a droop shift control strategy is proposed, taking into account the energy storage system (ESS) and its management with the virtual output power method. Simultaneously, the droop shift control can increase the load response in the DC side of BIC. During periods of low load demand, the ESS can be charged, and the overall power sharing on the AC and DC sides can be achieved. In addition, this study combines virtual impedance and frequency restoration control of BIC to enhance active and reactive power sharing. Furthermore, the system stability is analyzed. Finally, the feasibility of the proposed method is verified through simulations and prototype experimental results.

9 September 2019 in Applied Sciences
Verified
Journal Article
Open access
PDF file
YLYi-Hung Liao
Yi-Hung Liao
YLYue Lin
Yue Lin
This paper presents a bidirectional wireless power transfer system for mobile power applications. A novel 2-switch bidirectional wireless power transfer system with dual-side control is proposed for mobile power applications. Although only two switches are adopted, the energy can be transferred from the transmitter side to the receiver side and vice versa. The term bidirectional means that the power-flow is bidirectional and also that the transmitter is also a receiver and the receiver is also a transmitter. The output energy can be easily controlled by the duty ratios of the two switches. Thus, the proposed bidirectional power transfer system uses only one circuit to achieve bidirectional power transfer. Hence, the system cost and volume can be reduced so that the system is small and convenient for mobile power systems, portable and/or wearable electronic devices. A prototype system is constructed and the experimental results verify the validity of the proposed bidirectional wireless power transfer system.

1 January 2020 in Energies
Verified
Journal Article
Open access
PDF file
YLYi-Hung Liao
Yi-Hung Liao
A step up/down AC/DC converter with modified dual loop control is proposed. The step up/down AC/DC converter features the bridgeless characteristic which can reduce bridge-diode conduction losses. Based on the step up/down AC/DC converter, a modified dual loop control scheme is proposed to achieve input current shaping and output voltage regulation. Fewer components are needed compared with the traditional bridge and bridgeless step up/down AC/DC converters. In addition, the intermediate capacitor voltage stress can be reduced. Furthermore, the top and bottom switches still have zero-voltage turn-on function during the negative and positive half-line cycle, respectively. Hence, the thermal stresses can also be reduced and balanced. Simulation and experimental results are provided to verify the validity of the proposed step up/down AC/DC converter and its control scheme.