Oswald Prucker

Oswald Prucker

Auto-generated profile, based on publicly available information

Oswald Prucker

Department of Microsystems Engineering (IMTEK) Laboratory for Chemistry & Physics of Interfaces Albert‐Ludwigs‐Universität Freiburg Freiburg Germany

Research Focus & Metrics

Academic Career Length

23Years (2004-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 February 2024 in Small
Verified
Journal Article
Closed access
GEGozde Aktas Eken
Gozde Aktas Eken
YHYuming Huang
Yuming Huang
OPOswald Prucker
Oswald Prucker
JRJürgen Rühe
Jürgen Rühe
COChristopher Ober
Christopher Ober

28 November 2023 in Journal of Physics: Energy
Verified
Journal Article
Open access
PDF file
CLCarina Ludwig
Carina Ludwig
JLJan Leutner
Jan Leutner
OPOswald Prucker
Oswald Prucker
JRJürgen Rühe
Jürgen Rühe
Manfred KohlManfred Kohl
Manfred Kohl
We report on the design and characterization of a demonstrator device for miniature-scale elastocaloric (eC) cooling using a series of natural rubber (NR) foil specimens of 9 × 26.5 mm2 lateral size and thicknesses in the range of 290–900 μm. NR has the potential to meet the various challenges associated with eC cooling, as it exhibits a large adiabatic temperature change in the order of 20 K and high fatigue resistance under dynamic load, while loading forces are low. Owing to the large surface-to-volume ratio of rubber-based foils, heat transfer to heat sink and source elements is accomplished by mechanical contact enabling compact designs. Two actuators are implemented to control the performance in loading direction independent from the performance of mechanical contacting. The study of operation parameters is complemented by lumped-element modeling to understand the cycle frequency-dependent dynamics of heat transfer and resulting cooling capacity. The single-stage device operates in the strain range of 300%–700% and exhibits a temperature span up to 4.1 K, while the specific cooling power reaches 1.1 Wg−1 and the absolute cooling power 123 mW. The performance metrics show a pronounced dependence on foil thickness and heat transfer coefficient indicating a path toward future device optimization.

9 February 2025 in Advanced Functional Materials
Verified
Journal Article
Open access
RMRenato Maraula
Renato Maraula
MBMaryam Bahrami
Maryam Bahrami
SJSafora Jafari
Safora Jafari
OPOswald Prucker
Oswald Prucker
TATobias Amann
Tobias Amann
JRJürgen Rühe
Jürgen Rühe
The friction behavior of surfaces is investigated which are coated with surface‐attached hydrogel layers inspired by the structure of natural synovial joints. Photoinduced C,H insertion chemistry is used to form polymer networks from hydrogel precursor polymers and simultaneously link them to both sliding partners. As the crosslinking is performed in the dry state and all polymer chains are covalently bound to the surface, the hydrogel layers can only swell in one direction leading to strong chain stretching. This confinement leads to surfaces with ultralow adhesion and strongly reduces friction. The incorporation of charges and the addition of shear‐thinning polymers to the water phase allows for the generation of friction systems having coefficients of friction of µ = 0.002–0.001, thus reaching superlubricity and even surpassing the values reported for the properties of the natural model.

1 March 2005 in Polymer
Verified
Journal Article
Closed access
HKHyeonjae Kim
Hyeonjae Kim
HZHai Ning Zhang
Hai Ning Zhang
SNSuresh Narayanan
Suresh Narayanan
Jin WangJin Wang
Jin Wang
OPOswald Prucker
Oswald Prucker
MFMark D. Foster
Mark D. Foster

1 April 2015
Verified
Conference Paper
Closed access
CHChristina Hassler
Christina Hassler
NENils Ehler
Nils Ehler
VSVivek Singh
Vivek Singh
YXYijing Xie
Yijing Xie
NMNadja Martini
Nadja Martini
Thomas StieglitzThomas Stieglitz
Thomas Stieglitz
Within this study, flexible, polyimide based shaft electrodes were fabricated and dip-coated with a PDMAA-co-SSAz solution that formed a thin hydrogel layer on the electrode shanks. This layer stiffened the electrode for insertion when thoroughly dried. The electrodes were successfully implanted into a brain model and into real brain tissue of rodents. The insertion forces during in vitro and in vivo implantation were recorded and compared. Pre-pricking of an insertion channel didn't simplify the insertion in vitro in all cases. The final insertion forces were in vivo (15 - 58 mN) slightly higher than in vitro (12 - 20 mN). Electrochemical impedance spectra were recorded in vivo up to twelve weeks post implantation, measuring the impedance between two electrode sites through the hydrogel. Three types of impedance spectra were observed during the implantation period: mainly resistive spectra, mainly capacitive spectra and spectra showing resistive and capacitive components. One week after implantation, the amount of spectra with resistive-capacitive components was 90 % and decreased to 50 % in week twelve, while the amount of mainly resistive spectra increased from initially 2 % to 38 %. The amount of mainly capacitive spectra changed from 8 % in week one to 12 % in week twelve.

1 November 2004 in Bio-Medical Materials and Engineering
Verified
Journal Article
Closed access
MDManfred Dahm
Manfred Dahm
JRJürgen Rühe
Jürgen Rühe
BBBernd Berchthold
Bernd Berchthold
DPDiethard Prüfer
Diethard Prüfer
OPOswald Prucker
Oswald Prucker
HOHellmut Oelert
Hellmut Oelert
Reoperation of aldehyde tanned bioprotheses due to calcific degeneration remains their major drawback. Based on experiments studying mechanisms and factors that influence the time phase, extent and progression of calcification and evaluating the efficiency of anticalcification treatments and the effects of surface seeding with vital cells a new concept to avoid calcification emerged: masking aldehyde‐residues with a covalently bound polymer that supports surface cell seeding. Different covalently bound polymers were tested for their suitability to grow cells. Dense cell growth was achieved on some polymers but without correlation to physico‐chemical properties. Ultrathin coating of biological materials appears a promising approach to achieve lining with vital cells.