3 February 2020 in IEEE Transactions on Antennas and Propagation
An ellipsoidal Luneburg lens binary array is proposed and implemented for wide-angle scanning. In order to solve the occlusion problem between the lens elements in the array, the spherical Luneburg lens is transformed into the ellipsoidal Luneburg lens based on the transformation optics. The permittivity distribution of the Luneburg lens is revised to increase the lens’ aperture efficiency when the lens is not particularly large compared with the feed. Further, by introducing the local-beam shifting method, the number of feeds under each lens and the mutual coupling between the feeds can be reduced with the scanning characteristics remained. To validate the proposed design, a 1 × 2 ellipsoidal Luneburg lens array has been designed, fabricated and tested. Each ellipsoidal Luneburg lens with 110 mm long axis radius and 88 mm short axis radius is fabricated by means of 3D printing technology. Patch antennas operating at 2.25 GHz are employed as feeds. The measured results show that the proposed ellipsoidal Luneburg lens binary array can realize the maximum gain of 15.5 dB at zenith direction and 13.3 dB at 62°. The maximum scanning angle of ±68° can be achieved with a 3dB-gain reduction and −8 dB side-lobe.
17 September 2018 in IEEE Transactions on Antennas and Propagation
An X-band leaky waveguide antenna (LWA) with high aperture efficiency and high power capacity is investigated in this paper. The antenna is mainly composed of two parts, a sectorial waveguide power divider and a leaky waveguide antenna array. First, in the design of the power divider, the magnitude uniformity and phase consistency are ensured by adjusting the channel central angles and introducing phase adjusting structures respectively. Then, the analysis and design of the LWA array is carried out. New formulas and conditions have been proposed for realizing uniform radiation distribution and maximum aperture efficiency. Five supporting beams are introduced to increase the antenna gain and power capacity. An LWA array as a prototype is fabricated and tested to verify the analysis and simulation. Experimental results agree well with the simulation. The return loss is better than 17 dB at the center frequency 9.7 GHz, the gain is 38.75 dB, and the corresponding aperture efficiency is 80.7 %. The power capacity of the LWA array reaches 1.5 GW. These characteristics demonstrate that the proposed LWA array is suitable for radiating high power microwaves. The analysis and design method proposed in this paper is a useful guide for designing high aperture efficiency antenna in the future.
2 April 2020 in IEEE Transactions on Antennas and Propagation
Studying on the optimal radiation pattern of the feed of Luneburg lens for high gain application is the focus of this paper. Based on geometric optics and equivalent aperture theory, the effect of the radiation pattern of the feed on the gain of Luneburg lens is analyzed firstly. Then the optimal radiation pattern of the feed is predicted by theoretical calculation to guarantee the maximum radiation gain of Luneburg lens, and the halfpower beamwidth (HPBW) of the optimal radiation pattern of the feed is near 68° for the Luneburg lens with a radius greater than three wavelengths. To verify the theory, the Luneburg lens antennas fed by the feeds with different radiation patterns working at 10 GHz are analyzed. Finally, a prototype of Luneburg lens with a radius of 100 mm and several different feed antennas are manufactured to verify the theory and the simulation. The final simulated and measured results are consistent with the theory.
13 November 2024 in IEEE Antennas and Wireless Propagation Letters
A wide angle scanning circularly polarized (CP) concentric ring array (CRA) with large element spacing is proposed. With large element spacing, 75% transmitter/receiver components (T/Rs) can be saved compared with a traditional compact uniform array. In addition, two-unit elements are adopted to improve the aperture efficiency of the CRA. Meanwhile, sequential rotation technology and specially designed radiating unit are employed to achieve wide axial ratio (AR) bandwidth and wide gain bandwidth of the CRA. To verify the proposed method, a 64-element CP CRA working in frequency band of 7.15 ∼ 8.65 GHz (19%) with average element spacing of 1λ×1λ is designed, fabricated and measured. The CRA can scan from -50º to 50º in elevation plane for all azimuth direction with AR less than 4.2 dB, scan loss less than 6.9 dB, and aperture efficiency in Zenith direction higher than 44.7%
8 January 2021 in IEEE Transactions on Antennas and Propagation
In this paper, a design method for the reflectionless absorber (RLA) is proposed based on the principle of the band-stop reflectionless filter (RLF). Compared to the traditional absorbing structures, the RLA can effectively absorb the EM waves within its operating band with small out-band reflection. Besides, the RLA has layer-independent characteristic due to its small reflection. Therefore, multi-band and wideband RLAs can be achieved by simply stacking several single-band RLAs. After theoretical analysis and discussion of the single-band RLA, multi-band and wideband RLAs are designed. Finally, two samples are fabricated to verify the presented design method. The theoretical calculated, simulated and measured results agree well.
8 January 2021 in IEEE Transactions on Antennas and Propagation
In this paper, absorbers with open boundary condition are analyzed theoretically. Firstly, a complex analysis method is employed to obtain integrations of the reflection and transmission over the whole frequency band for slab with general boundary condition, which can be regarded as a general extension of the Rozanov’s discussion. Secondly, integration relations with open boundary condition for single-layer slab and multi-layer slab are obtained successively. Thirdly, theoretical limitations for the absorbers with open boundary condition are deduced. As an application, complete analytic limitations between the reflection, transmission, operating band and thickness are provided for single-layer non-magnetic absorber with small reflection and transmission required. Finally, after presenting optimal design method for single-layer non-magnetic slab, several absorbers are designed as examples.