20 April 2021 in The International Journal of Advanced Manufacturing Technology
Laser cladding is a well-established technique, with the majority of prior numerical modelling work focused on delivery and melt pool behaviour of powder-based processes. This research presents new investigations into optimised laser beam shaping for the unique characteristics of wire-based processes, where direct substrate heating, as well as heat transfer between the wire and substrate, is important. The value of this subject is the improved deposition rates and dense metallic structures that can be achieved by wire-based deposition processes compared to powder-based material delivery. The within-wire temperature distribution (AISI 316 stainless steel), the heat transfer and direct heating of the substrate (mild steel) are modelled via heat transfer simulations, with three laser beam irradiance distributions. This analysis identified the removal of localised high-temperature regions typically associated to standard Gaussian distributions, and the improved substrate heating that a uniform square beam profile can provide. Experiments using pre-placed wire and a 1.2 kW CO2 laser were analysed using cross-sectional optical microscopy to provide model validation and evidence of improved wire-substrate wetting, while maintaining favourable austenitic metallurgy in the clad material. A key finding of this work is a reduction, from 480 to 190 W/mm2, in the required irradiance for effective melt pool formation when changing from a Gaussian distribution to a uniform square distribution. This also provided a 50% reduction in total energy. The potential improvements to energy efficiency, cost reductions and sustainability improvements are recognised and discussed.
28 September 2023 in International Journal of Precision Engineering and Manufacturing-Green Technology
In an increasingly technological world, energy efficiency in manufacturing is of great importance. While large manufacturing corporations have the resources to commission energy studies with minimal impact on operations, this is not true for small and medium enterprises (SME’s). These businesses will commonly only have a small number of laser processing cells; thus, to carry out an energy study can be extremely disruptive to normal operations. Since rising global energy costs also have the largest impact on small businesses who lack the benefit of economies of scale, they are simultaneously the most in need of improvements to energy efficiency, while also facing the strongest practical barriers to implementing them. In this study, a laser processing energy analysis methodology was designed to run simultaneously with normal operation and applied to a laser shim-cutting cell in a UK-based SME. This paper demonstrates the methodology for identifying operating states in a production environment and Specific Energy Consumption and Scope 2 CO2 emissions results are analysed. The Processing state itself was the most impactful on overall energy performance, at 55% for single sheets of material, increasing to 71% when batch processing. Generating idealised data in this production environment is challenging with restrictions to isolating variables, these “real-world” limitations for conducting system energy analysis simultaneously with live production are also discussed to present recommendations for further analysis.
25 October 2022 in Journal of Laser Applications
Laser material interactions are routinely praised for their selective processing and high processing rates. However, this does not guarantee that the total manufacturing system has a low energy intensity compared to conventional manufacturing processes. This paper presents the results of a collaborative UK and China research project to improve the comprehension of the total energy consumption and carbon emissions for laser-based manufacturing. A range of individual laser cutting, welding, and cleaning processes were studied to assess their energy efficiency, including the laser and its ancillary subsystems (e.g., cooling and extraction). The project developed a systematic analysis method, adapted from BS ISO 14955-1:2017, which incorporated time and subsystem level studies to quantify all energy consumption components of a laser system. Previous research has identified that the laser system's most significant contributor to the total energy consumption are the auxiliary or supporting subsystems, not the laser emission. This identified that using only the absorbed radiation to evaluate manufacturing efficiency is misleading. All the processes evaluated followed a negative correlation between processing rate (kg/h) and specific energy consumption (J/kg). The new data conclude that laser processes have a relatively high energy intensity compared to conventional manufacturing alternatives. The results can be used to identify where the most significant improvements to individual laser systems can be made. The comprehensive comparison of processes allows manufacturers to select processes to improve environmental impact.
4 July 2017 in European Journal of Engineering Education
The supply of students motivated to study engineering in higher education is critical to the sector. Results are presented from the ‘Mindsets STEM Enhancement Project’. Fifty-seven new resources packs, designed to improve STEM education in Design and Technology, were given to schools across London. A modified Intrinsic Motivation Inventory questionnaire measured pupils’ (n = 458) motivation towards technology. The results show that although pupils have positive reactions to the technology content within Design and Technology lessons, the type of STEM resources and lessons created through the project had made no significant difference on pupils’ interest/enjoyment towards technology. This suggests stand-alone resources do not improve pupil motivation. The impact of this work to engineering higher education is that the existing levels and the inability to improve pupil motivation in technology at school could be a factor affecting the pursuit of a technology or engineering related education or career.
7 August 2019 in International Journal of Technology and Design Education
Secondary school, age range 11–14, technology and engineering education in England has been delivered mainly within Design and Technology (D&T). This inadvertently makes D&T teachers responsible for pupils’ engineering education and motivation. This paper analyses D&T teachers’ (N = 33) technology subject knowledge through self-assessment competency questionnaires, before and after developing a Science, Technology, Engineering and Mathematics (STEM)-focused project of their choice for their classroom. Participants were least confident in teaching the areas of technology that required mathematics and scientific knowledge. The results analyse a suggested misalignment between teachers’ Creative Arts background subject knowledge compared to the technology subject knowledge required for engineering education. Suggested causes of this issue are Initial Teacher Training standards and curriculum flexibility, not teacher capability. The paper concludes that teachers have been unaware of some elements of STEM education and that continuing professional development interventions are required to assist teachers and improve their engineering knowledge in order to better equip their pupils for engineering.
9 March 2021 in Journal of Laser Applications
The hazard of surgical smoke is often overlooked when considering the safety of medical laser procedures but can present a high level of occupational risk. Administrative procedures for operating external extraction devices and the reliance on personal protective equipment are not sufficient for reducing the risk. This paper aims to quantify the hazard of laser-generated surgical smoke and demonstrate how effective engineering control solutions can reduce the risk. A new design solution is presented with engineering controls for surgical smoke extraction and optical radiation integrated into the laser handpiece. A fiber delivered diode laser is used to simulate laser vaporization procedures on porcine skin tissue. Conventional external extraction conditions are compared to the new design solution. Fine particulate mass concentrations (PM2.5) from the simulated procedures, under different extraction conditions, are measured using optical particle size measurements. Peak concentrations of 55.86 ± 2.79 μg/m3 were measured without extraction; showing that the hazard of laser-generated surgical smoke is five times greater than the World Health Organization guideline of 10 μg/m3. A typical medical extraction setup only achieved a 16% reduction in peak concentration values, 47.07 ± 2.35 μg/m3; demonstrating that conventional, external, methods of extraction are ineffective. The new solution was able to capture all particulate materials, reducing particulate concentrations to background levels, 2.19 ± 0.68 μg/m3, safely below the current recommended guidelines. The design and results present evidence that it is not only more effective to use engineering control methods but that it is practicable to do so.