Rebecca L. Higginson

Rebecca L. Higginson

Auto-generated profile, based on publicly available information

Rebecca L. Higginson

Department of Materials, Loughborough University, Loughborough, UK

Research Focus & Metrics

Academic Career Length

28Years (1999-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 1999 in Acta Materialia
Verified
Journal Article
Closed access
RHR Higginson
R Higginson
PBP Bate
P Bate

20 April 2021 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Open access
PDF file
NGNicholas Goffin
Nicholas Goffin
JTJohn R. Tyrer
John R. Tyrer
LJLewis Jones
Lewis Jones
RHRebecca L. Higginson
Rebecca L. Higginson
Laser cladding is a well-established technique, with the majority of prior numerical modelling work focused on delivery and melt pool behaviour of powder-based processes. This research presents new investigations into optimised laser beam shaping for the unique characteristics of wire-based processes, where direct substrate heating, as well as heat transfer between the wire and substrate, is important. The value of this subject is the improved deposition rates and dense metallic structures that can be achieved by wire-based deposition processes compared to powder-based material delivery. The within-wire temperature distribution (AISI 316 stainless steel), the heat transfer and direct heating of the substrate (mild steel) are modelled via heat transfer simulations, with three laser beam irradiance distributions. This analysis identified the removal of localised high-temperature regions typically associated to standard Gaussian distributions, and the improved substrate heating that a uniform square beam profile can provide. Experiments using pre-placed wire and a 1.2 kW CO2 laser were analysed using cross-sectional optical microscopy to provide model validation and evidence of improved wire-substrate wetting, while maintaining favourable austenitic metallurgy in the clad material. A key finding of this work is a reduction, from 480 to 190 W/mm2, in the required irradiance for effective melt pool formation when changing from a Gaussian distribution to a uniform square distribution. This also provided a 50% reduction in total energy. The potential improvements to energy efficiency, cost reductions and sustainability improvements are recognised and discussed.

1 March 2015 in Materials Science and Technology
Verified
Journal Article
Open access
GGG. Green
G. Green
RHR. Higginson
R. Higginson
SHS. Hogg
S. Hogg
SSS. Spindler
S. Spindler
CHC. Hamm
C. Hamm
JNJens Najorka
Jens Najorka
A significant fraction of ferrite has been identified in a 321 grade austenitic stainless steel in the solution heat treated condition. The microstructures were analysed using electron backscatter diffraction, energy dispersive X-ray spectroscopy and X-ray diffraction (XRD) and the stability of the ferrite investigated using heat treatments in a tube furnace, dilatometry and high temperature XRD. The ferrite dissolved ∼800°C, then formed again on cooling at temperatures under 200°C. Thermodynamic predictions showed a significant ferrite content at room temperature under equilibrium conditions, and the DeLong diagrams predict an austenite+martensite microstructure in the cast condition. Sensitivity analysis on the DeLong diagram has shown that the nitrogen content had a large effect on the austenite stability. The instability of the austenite and the subsequent transformation to ferrite on cooling can be attributed to low nitrogen content measured in the as received material. It was found that thermal aging of the material caused further transformation of austenite to ferrite as well as the formation of sigma phase that appears higher in nitrogen than the matrix phases. The diffusion of nitrogen into sigma phase may cause instability of the austenite, which could cause further transformation of austenite to ferrite on cooling from the aging temperature. The transformation of austenite to ferrite is known to be accompanied by an increase in volume, which may be of relevance to components made with tight dimensional tolerances.

16 March 2022 in Transactions of the IMF
Verified
Journal Article
Open access
GAG. T. Alliott
G. T. Alliott
RHR. L. Higginson
R. L. Higginson
GWG. D. Wilcox
G. D. Wilcox
Stainless steels are often used for decorative purposes, primarily in the architectural industry, but also in homeware and the automotive industry, among others. It is possible to impart colour on articles to enhance aesthetics without impairing the desirable properties of the stainless steel itself. The colour can be non-iridescent and created by the absorbance of light waves of all but a given wavelength, or iridescent and created by a phenomenon known as thin-film interference. Colouring methods have been categorised into three groups, electrochemical, non-electrochemical and laser colouring. Laser colouring can be utilised as either an electrochemical or non-electrochemical process. The colouring technique most widely adopted by industry is a 2-stage electrochemical process, known as the INCO process, which utilises chromic-sulphuric acid baths to produce a thin interference film on the stainless steel surface. Alternatives developed by investigators regularly cite the toxicity of hexavalent chromium as motivation for their work and use the INCO process as a benchmark. Authors claim that alternative techniques match or exceed many of the properties achieved through colouring using hexavalent chromium, however, none are yet widely adopted by industry for the purpose of colouring stainless steel. It is therefore important to consider each technique to understand why this is the case. Part 1 of this review discusses the electrochemical processes utilised to produce coloured films on stainless steel, and Part 2 discusses non-electrochemical and laser processes.

23 June 2025 in Materials Today Communications
Verified
Journal Article
Open access
MAMolly Appleton
Molly Appleton
MJMark A.E. Jepson
Mark A.E. Jepson
RHRebecca L. Higginson
Rebecca L. Higginson