29 September 2020 in IEEE Internet of Things Journal
Ranging from circuit-level characterization to designing a platform architecture, developing a design automation tool, and fabricating an system-on-chip (SoC), this paper deals with the entire development process for ultra-low power (ULP) SoCs for Internet of Things endnodes. More precisely, this paper first focuses on the unique characteristics of the ULP circuits, the temperature effect inversion (TEI), i.e., the delay of the ULP circuits decreases with increasing temperature. Existing TEI-aware low power (TEI-LP) techniques have incredible potential to further reduce power consumption of conventional ULP SoCs, but there is a critical limitation to be widely adopted in real SoCs. To address this limitation and realize the ULP SoCs that can fully benefit from the TEI-LP techniques, this paper proposes a new TEI-inspired SoC platform (TIP) architecture. On top of that, taking into account that the highly complex, time-consuming and labor-intensive development process of these ULP SoCs may hinder their widespread use for IoT endnodes, this paper presents a new EDA tool to accelerate ULP SoC development, RISC-V eXpress (RVX). Finally, By using the RVX, this paper introduces a TIP prototyping chip fabricated in 28nm FD-SOI technology. This chip demonstrates that power savings of up to 35% can be achieved by lowering the supply voltage from 0.54V to 0.48V at 25 and 0.44V at 80 while continuing to operate at a target 50MHz clock frequency.
18 July 2024 in IEEE Transactions on Circuits and Systems I: Regular Papers
The increasing interest in RISC-V from both academia and industry has motivated the development and release of a number of free, open-source cores based on the RISC-V instruction set architecture. Specifically, the use of lightweight RISC-V cores in processors tailored for IoT endnode devices is on the rise. As the range and complexity of these applications grow, there is an increasing demand for multicore processors that can handle floating-point operations. This poses a significant challenge because most lightweight RISC-V cores are integer cores lacking a floating-point unit (FPU). This limitation makes it difficult to design processors optimized for applications that require floating-point operations concurrently with integer operations. While it is inefficient to have a dedicated FPU per core in a multicore processor (because it would give rise to unnecessary power consumption), it is crucial to find a solution that balances performance and energy efficiency. To address this challenge, we propose to utilize an external lightweight FPU that can be added to any RISC-V integer core, along with a low-power multicore architecture that shares the said FPU. We have applied this concept to design a RISC-V processor that integrates these technologies, implemented it on an FPGA device, and completed the fabrication of a System-on-Chip for functional verification. Our experiments, which involved testing various applications on different processor prototypes, demonstrated significant energy savings of up to 79.6% in a quad-core processor prototype, highlighting the potential energy efficiency of our proposed technology.
31 January 2020 in IEEE Transactions on Instrumentation and Measurement
Human body communications (HBC) has recently emerged as an innovative alternative to the current radio frequency communications for realizing wireless body area networks (WBAN) using the human body as a transmission channel without wired or wireless connections. This study addresses the provision of reliable modeling of the human body as a passage of the electric signal delivery based on the impulse response measurement through the proposal of a measurement setup and signal processing techniques applicable to wearable devices for healthcare and bio-signal acquisition. In the experiments, customized impulse signals were applied to the body using battery-powered devices isolated to the earth-ground for the operating environments of wearable devices. The impulse responses passed through the body were measured considering 52 measurement conditions determined by the device locations from the head to ankle, and the body postures. Body channel transfer functions (BCTFs) for the respective conditions were derived by an adaptive filter approach using an iterative algorithm to minimize the mean squared error between the measured and modeled impulse responses. The channel analysis parameters, such as mean path-loss, root-mean-square delay spread, and mean and maximum excess delays were analyzed based on the measured body impulse responses. In addition, the practical bit-error-rate performance for HBC based on the BCTFs reproducing inter-symbol interference effects caused by the delay spreads of the body channels were explored to verify communication reliability in terms of the transmitter structures adopting digital transmission, sorts of human body channels, data rates, and operating frequencies.
12 April 2017 in IEEE Transactions on Computer-Aided Design of Integrated Circuits and Systems
The era of the Internet of Things (IoT) is upon us. In this era, minimizing power consumption becomes a primary concern of system-on-chip designers. Ultralow power (ULP) very large-scale integration circuits have been receiving considerable interest from both academia and industry as the best-suited techniques for IoT devices, which can take full advantage of power-saving that voltage scaling potentially achieves. Consequently, research on ULP designs has begun to yield tangible outcomes, namely ULP circuits. However, little attention has been paid to ULP network-on-chip (NoC), although the NoC is an essential of the ULP chips, and its power consumption accounts for a significant portion of the total power. This paper focuses on ULP NoCs, and presents a new power management method that exploits delay versus temperature characteristics of ULP circuits. Recent studies on ULP circuits show that delay versus temperature characteristics are fundamentally different from normal circuits, i.e., the delay of the ULP circuits implemented in state-of-the-art bulk CMOS operating at low supply voltages or in FinFET technologies decreases with increasing temperature, a phenomenon known as the temperature effect inversion (TEI). Starting with an intuition that at a certain temperature point, power savings without performance penalty can be achieved by increasing the router frequency to create the opportunity to turn off some routers in ULP NoCs, or by decreasing the NoC supply voltage level, an optimization method is presented to maximize the power savings with minor performance penalty. To validate the proposed method, a concrete ULP NoC simulator, TEI-Noxim, has been developed. Experimental results demonstrate that TEI-aware NoC achieves an average of 36.0% power reduction over 21 applications.