1 January 2022 in Journal of Aircraft
Future aircraft designs look set to use longer wingspans to increase the aspect ratio and therefore overall aerodynamic efficiency of the airframe. Such larger wingspans also reduce roll rates and ...
1 March 2023 in Journal of Aircraft
High-aspect-ratio wings are of particular interest to modern aircraft design due to the inherent reduction in induced drag that they provide. However, such wing configurations often come with problems such as increased structural weight and oversized wingspans for existing airport facilities. Unlike conventional folding wingtips, as used on the 777-X, this paper demonstrates the use of semi-aeroelastic hinge devices that enable aircraft incorporating high-aspect-ratio wings not only to fit into airport gates, but also to alleviate aerodynamic loads by allowing floating wingtips to be used in-flight. This study establishes a preliminary design process for such a wing configuration and undertakes a comprehensive sizing process to investigate the impact of the device on wing weight and aircraft performance. For the cases considered, a reduction in wing weight of approximately 25% can be achieved by utilizing the semi-aeroelastic hinge, which can lead to more than 5% improvement in aircraft range.
1 March 2023 in Journal of Aircraft
Recent studies have considered the use of flared folding wingtips (FFWTs) to enable higher aspect ratios—reducing overall induced drag—while reducing gust loading and meeting airport operational requirements. The majority of these analyses have employed linear assumptions despite the presence of large wingtip deformations. In this paper the effect of geometric nonlinearities introduced by an FFWT on the static and dynamic aeroelastic response of a wing is assessed. A geometrically exact expression was formulated to describe the change in the local angle of attack in the chordwise direction across all fold angles. This expression highlighted that the aerodynamic stiffness of an FFWT and, therefore, quantities such as the linear flutter speed are a function of the fold angle and, hence, the attitude of the wing. This effect was verified using both a wind tunnel model of a flexible semispan wing and a numerical model utilizing MSC Nastran, which linearized the model about the equilibrium position of the wingtip. These experiments showed that the geometric nonlinearities introduced due to the large deformations of FFWTs can significantly affect the dynamics of the system, with flutter speeds varying by over 28%, simply by changing the angle of attack of the model.
1 January 2024 in Journal of Aircraft
Recent studies have considered the use of wings incorporating flared folding wingtips (FFWTs) to enable higher aspect ratios (reducing overall induced drag) while also reducing gust loading and meeting airport operational requirements. This paper presents the first experimental research into the nonlinear dynamic behavior of a wing incorporating an FFWT. Wind-tunnel tests were conducted at a range of velocities below and beyond the linear flutter boundary. The experimental findings are compared with results obtained from continuation and bifurcation analyses on a representative low-fidelity numerical model. The results show that beyond the linear flutter boundary, stable limit cycle oscillations form, which is dependent on the flare angle, are bounded by either geometric or aerodynamic nonlinearities. Also presented is the effect of a wingtip trim tab on the stability boundary of a wing incorporating FFWTs. It is found that the tab angle can significantly alter the stability boundary of the system, indicating that the choice of camber is an important parameter when considering the stability boundary of FFWTs and that a moveable control surface on an FFWT could be used “in flight” to extend the stability boundary of an aircraft.
1 May 2024 in Journal of Aircraft
Recent studies have shown that semi-aeroelastic hinge devices can enable larger aircraft wingspans. Such a device would be folded on the ground to meet airport width restrictions, locked during cruise for optimal aerodynamic performance, and released during maneuvers to alleviate flight loads. In contrast, this paper uses a wind tunnel experiment to study the aeroelastic behavior of floating wingtip fuel tanks. This device consists of a freely floating wingtip with an additional mass attached in the form of a liquid-filled fuel tank. The static aeroelastic results show that altering the fuel tank’s filling level and position allows the wingtip to float at an optimal angle for aerodynamic efficiency across various angles of attack and fuel masses. Additionally, this paper shows that, with careful selection of the mass distribution of the wingtip, dynamic load alleviation comparable to the semi-aeroelastic hinge concept can be achieved during turbulence and one-minus-cosine encounters. Furthermore, the effect of fluid motion is shown to reduce incremental loads during random turbulence encounters by up to 10%; however, it has a negligible impact on the response to one-minus-cosine encounters. Such results are also confirmed by a numerical model incorporating a simple reduced-order fluid sloshing model.
17 April 2024 in AIAA Journal
There has been a growing interest in utilizing flared folding wingtips as an in-flight load alleviation device to enable increased wing spans that meet airport gate limits but with little increase in wing weight. The semi-aeroelastic hinge (SAH) concept is implemented in high-aspect-ratio wings to enable wingtips to be released during severe load cases such as maneuvers and gusts to alleviate the bending moments while maintaining optimum aerodynamic shape for the rest of the flight. In this paper, scaling methods for wings incorporating the SAH are explored, allowing for the development of equivalent scaled unmanned aerial vehicles or wind tunnel models with similar aeroelastic behavior as full-size aircraft. Three scaling approaches are considered in this study, namely, Iso-Froude, Iso-Frequency, and Iso-Strain, where a set of governing nondimensional quantities and scaling factors are determined. Despite the significant nonlinearities resulting from large wingtip fold angles, it is shown that a linear scaling approach can be appropriate for such a wing configuration. Furthermore, the aeroelastic properties of each scaled model are compared to those of the full-scale model, where the best match was obtained from the Iso-Strain model, although it is challenging to meet the required operational conditions.