Lithium-ion cells testing under different state of charge ranges, C-rates and cycling temperature have different degrees of lithium inventory loss, impedance growth and active mass loss. Here, a large matrix of polycrystalline NMC622/natural graphite Li-ion pouch cells were tested with seven different state of charge ranges (0-25, 0-50, 0-75, 0-100, 75-100, 50-100 and 25-100%), three different C-rates and at two temperatures. First, capacity fade was compared to a model developed by Deshpande and Bernardi. Second, after 2.5 years of cycling, detailed analysis by dV/dQ analysis, lithium-ion differential thermal analysis, volume expansion by Archimedes’ principle, electrode stack growth, ultrasonic transmissivity and x-ray computed tomography were undertaken. These measurements enabled us to develop a complete picture of cell aging for these cells. This then led to an empirical predictive model for cell capacity loss versus SOC range and calendar age. Although these particular cells exhibited substantial positive electrode active mass loss, this did not play a role in capacity retention because the cells were anode limited during full discharge under all the tests carried out here. However, the positive electrode mass loss was strongly coupled to positive electrode swelling and electrolyte “unwetting” that would eventually cause dramatic failure.
11 November 2019 in Journal of the Electrochemical Society
Electrolyte additives are a practical route to improving the lifetime and performance of lithium-ion cells. It is not well understood what makes a good additive; thus, the discovery of new additives poses a significant challenge. Computational methods have the potential to streamline the search for new additives, but it is important to compare predicted additive behavior with experimentally measured results. A new electrolyte additive, 1,3-dimethyl-2-imidazolidinone (DMI), has been evaluated in LiNi1-x-yMnxCoyO2 (NMC)/graphite pouch cells as a single additive and with the co-additive vinylene carbonate (VC). This work compares the density functional theory (DFT)-predicted behavior of DMI with experimental results, including differential capacity analysis (dQ/dV), electrochemical impedance spectroscopy (EIS), high-temperature storage, gas chromatography-mass spectrometry (GC-MS) and long-term cycling tests. The DFT-calculated reduction potential of DMI is −0.63 V vs Li/Li+, consistent with the experimental observation that it reduces at a lower potential than ethylene carbonate (EC), ∼0.80 V vs Li/Li+. Although DMI turns out not to be a competitively useful additive, the good match between many aspects of the experimental results and theoretical predictions is a good indication that it is possible to understand aspects of the behavior of additives. This can guide future researchers.
1 October 2020 in Journal of the Electrochemical Society
The effects of different duty cycles, involving mixtures of charge-discharge cycling and open-circuit storage segments, on the lifetime of single crystal NMC532/graphite cells were studied. Charge-discharge cycling was performed at C/3 with open circuit storage times of 0, 12, 84, 180 h or 3 months applied at upper cutoff voltages (UCV) of 4.1, 4.2 and 4.3 V. Testing was made at 40 °C for a period of 2.5 years. Cells tested to the same UCV showed similar capacity loss and impedance growth with time, independent of the ratio between the time spent cycling or in storage. Differential voltage analysis showed that the vast majority of the capacity loss stemmed from lithium inventory loss at the negative electrode with little or no loss of active materials. The thickness of the pouch cells after testing increased with the fraction of time spent cycling and the amount of gas generated in the cells increased with fraction of time spent in storage at the UCV. These results show that cycled and stored cells age differently, even though a similar capacity fade rate was observed in the first 2.5 years of cell life, which may cause different failure modes at the end of cell life.
5 January 2020 in Journal of the Electrochemical Society
Finding new electrolyte additives could help create lithium-ion batteries with better performance at high voltage, allowing higher energy density. However, finding the perfect additive remains a tremendous challenge, since researchers still don’t understand how to predict their performance. A new group of dioxazolone electrolyte additives have been tested in lithium-ion batteries alone or in combination with well-known co-additives. The new additives consist of a 3-phenyl-1,4,2-dioxazol-5-one (PDO) parent structure with or without (methoxy, fluoro and nitro) functional groups on the para position of the phenyl ring. It is found that PDO (no functional group) and p-(4-nitrophenyl)-1,4,2-dioxazol-5-one (pNDO) are the best performing dioxazolones overall and show promising results.