Andreas Grau

Andreas Grau

Auto-generated profile, based on publicly available information

Andreas Grau

Karlsruhe Institute of Technology (KIT), Karlsruhe, Germany

Research Focus & Metrics

Academic Career Length

28Years (1999-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
25 October 2005 in Physical Review B
Verified
Journal Article
Closed access
PDF file
MGMassimo Galluppi
Massimo Galluppi
LGLutz Geelhaar
Lutz Geelhaar
HRHenning Riechert
Henning Riechert
MHMichael Hetterich
Michael Hetterich
AGAndreas Grau
Andreas Grau
WSWolfgang Stolz
Wolfgang Stolz
We present an extensive study leading to a general understanding about the optical transitions involved in the surface photovoltage (SPV) spectra of type-I quantum well (QW) structures. SPV measurements were carried out on In0.3Ga0.7As∕GaAs QW samples with varying QW width and on In0.15GaAs0.85∕AlxGa1−xAs QW samples with varying aluminum content. The results are compared with experimental electroreflectance spectra, absorption spectra simulated with multiband k∙p computations, and theoretical calculations of the electronic states in the QWs. Thus, the transitions which induce steps in the SPV spectra are unambiguously identified. Most remarkably, the bound electron-to-free hole transition is detected by SPV measurements. This distinguishes the SPV method from many other optical techniques like photoluminescence and photoreflectance spectroscopy that allow only the observation of bound-to-bound and free-to-free transitions. The analogous free electron-to-bound hole transition does not give rise to a feature in the SPV spectra. In addition, the bound-to-bound transitions e1−hh1, e1−lh1, and e2−hh2 are observed, if the respective states are confined. Also, the free-to-free transition ce−ch is measured. We demonstrate how these transitions can typically be identified in the spectra without any further measurements or calculations. With this knowledge, the practical band offsets of the QW structure, i.e., the energy difference between the lowest confined states in the QW and the extended states in the barrier, can be extracted directly from the spectra. An advantage over conventional techniques for the determination of band offsets is that neither any additional knowledge of other QW parameters nor simulations are necessary. As an example for the application of the SPV technique, the electronic states and band offsets of a series of In0.3Ga0.7As0.98N0.02∕GaAs QWs with varying QW width are characterized. These experiments directly show that nitrogen affects only the conduction band states.

9 November 2010 in IEEE Transactions on Applied Superconductivity
Verified
Journal Article
Closed access
SCSara Casalbuoni
Sara Casalbuoni
TBTilo Baumbach
Tilo Baumbach
SGStefan Gerstl
Stefan Gerstl
AGAndreas Grau
Andreas Grau
MHMichael Hagelstein
Michael Hagelstein
WWWolfgang Walter
Wolfgang Walter
In this contribution we report the results of the training and of the local field measurements performed in a liquid helium bath of the ANKA superconducting undulator. The period length is 15 mm and the coils are 1.5 m long. The key specifications of the system are an undulator parameter K higher than 2 (for a magnetic gap of 5 mm) and a phase error smaller than 3.5 degrees. The superconducting undulator is planned to be installed in the ANKA storage ring by the beginning of 2011 to be the light source of the new beamline NANO for high resolution X-ray diffraction..

11 January 2018 in IEEE Transactions on Applied Superconductivity
Verified
Journal Article
Closed access
AGAndreas Grau
Andreas Grau
SCSara Casalbuoni
Sara Casalbuoni
NGNicole Glamann
Nicole Glamann
THTomas Holubek
Tomas Holubek
DJDavid Saez de Jauregui
David Saez de Jauregui
WWWolfgang Walter
Wolfgang Walter
Since several years the Institute for Beam Physics and Technology (IBPT) of the Karlsruhe Institute of Technology (KIT) is collaborating with its industrial partner Babcock Noell GmbH (BNG) in a R&D program on superconducting undulators (SCUs). At present the collaboration is primarily working on a SCU with a period length of 20 mm (SCU20). This device is foreseen to be installed at ANKA, the test facility and synchrotron radiation source, run by the IBPT. The 1.5 m long undulator coils have been tested in a horizontal, conduction - cooled measurement setup. This contribution describes the training, the stability and the thermal behavior of the coils.

6 January 2011 in IEEE Transactions on Applied Superconductivity
Verified
Journal Article
Closed access
SCSara Casalbuoni
Sara Casalbuoni
TBTilo Baumbach
Tilo Baumbach
SGStefan Gerstl
Stefan Gerstl
AGAndreas Grau
Andreas Grau
MHMichael Hagelstein
Michael Hagelstein
RJRoger Jones
Roger Jones
One of the still open issues for the development of superconducting insertion devices is the understanding of the heat load induced by the beam passage. With the aim of measuring the beam heat load to a cold bore and in order to gain a deeper understanding in the beam heat load mechanisms, a cold vacuum chamber for diagnostics is under construction. We plan to have access with the same set-up to a number of different diagnostics, so we are implementing: i) retarding field analysers to measure the electron flux, ii) temperature sensors to measure the total heat load, iii) pressure gauges, iv) and mass spectrometers to measure the gas content. The inner vacuum chamber will be removable in order to test different geometries and materials. COLDDIAG is built to fit in a short straight section at ANKA, but we are proposing its installation in different synchrotron light sources with different energies and beam characteristics. A first installation in DIAMOND is planned in June 2011. Here we describe the technical design report of this device and the planned measurements with beam.

11 January 2018 in IEEE Transactions on Applied Superconductivity
Verified
Journal Article
Closed access
SCSara Casalbuoni
Sara Casalbuoni
NGNicole Glamann
Nicole Glamann
AGAndreas Grau
Andreas Grau
THTomas Holubek
Tomas Holubek
DJDavid Saez de Jauregui
David Saez de Jauregui
WWWolfgang Walter
Wolfgang Walter
The Institute for Beam Physics and Technology (IBPT) of the Karlsruhe Institute of Technology (KIT) and Babcock Noell GmbH (BNG) are collaborating to develop superconducting undulators for ANKA and low emittance light sources. The collaboration is now focusing on a superconducting undulator with a period length of 20 mm (SCU20) planned to be the source of the NANO beamline at ANKA. The local magnetic field and the field integrals of the SCU20 1.5 m-long-coils have been characterized in a conduction cooled horizontal test facility developed at KIT IBPT. Here we complement the main results reported in a previous work with a more detailed analysis, including the measurements of the geometrical deviations from the ideal case of the undulator coils at room temperature used to simulate the magnetic field profile with the program Radia and a quantitative explanation of the magnetic field measurements in cold conditions. A comparison of the photon spectrum calculated from the measured field with the one from the field simulated with Radia considering the geometry measured at room temperature is also presented.

17 January 2024 in IEEE Transactions on Applied Superconductivity
Verified
Journal Article
Closed access
BKB. Krasch
B. Krasch
FAF. Abusaif
F. Abusaif
TAT. Arndt
T. Arndt
NGN. Glamann
N. Glamann
AGA. Grau
A. Grau
DJD. Saez de Jauregui
D. Saez de Jauregui
Undulators are X-ray sources which are widely used in synchrotron storage rings and free-electron laser (FEL) facilities. As the development of future light sources envisages smaller and more compact undulators, it is necessary to construct small-scale high-field undulators with short period lengths $\lambda \,< $ 10 mm and narrow magnetic gaps $d_\text{mag} < $ 4 mm. Therefore, high-temperature superconducting (HTS) tapes are a promising candidate, since they offer a high critical current density at higher temperatures. Instead of the commonly used wounded coils of low-temperature superconducting (LTS) wires, such as NbTi, to generate the alternating magnetic dipole field, a meandering pattern is structured on the surface of the HTS tape with ps laser pulses to provide a sinusoidal current path through the tape, see Fig. 1 . This technique leads to a precise structure and at the same time prevents damage to the superconducting layer due to overheating. A new concept has been developed and improved at KIT. The new concept involves two opposing stacks of 30 laser-structured HTS tapes. The ends of each tape are soldered and connected to the tape above, resulting in an accordion-like arrangement, see Figs. 2 and 3 . This paper presents the general design and the preparation of the stacks of the compact SCU, followed by the results of a Biot-Savart magnetic field simulation. The magnetic field measurement setup and a first current carrying test of the two coils are included.