The parallel stator poles structure and concentrated field winding configuration of the doubly salient electromagnetic motor (DSEM) lead to the asymmetric three-phase flux paths and thus causing the significant d -axis and q -axis voltage harmonics. In the conventional flux weakening control methods, these d -axis and q -axis voltage harmonics are not considered, which will cause the deviation between the computed voltage and the actual voltage and reduce the dc-link voltage utilization. In this article, an improved flux weakening control method considering the d -axis and q -axis voltage harmonics induced by the asymmetric three-phase flux paths is proposed for the DSEM. First, the asymmetric three-phase flux paths of the DSEM are analyzed in this article. Then, the voltage equation considering the asymmetric three-phase flux paths is derived and verified. The current and voltage constraint are constructed and the reference current curves at different speeds are obtained through the proposed offline method. Finally, the proposed flux weakening control method is implemented on the 12/8-pole DSEM drive system. The experimental results indicate that the proposed flux weakening control method can improve the dc-link voltage utilization, effectively extend the constant torque region, and enhance the output power and torque capability of the DSEM drive system.
22 August 2023 in IEEE Transactions on Power Electronics
The direct instantaneous torque control (DITC) method is an effective way to suppress the torque ripple of doubly salient motor (DSM). However, there is the inevitable phase current peak in the conventional DITC method, which increases the current stress of the power switches and degrades the torque capability of the DSM. In this paper, an improved DITC method is proposed based on the optimal torque sharing ratio. Firstly, the maximum torque characteristics of two-segment twisted-rotor DSM are obtained through the finite element method. The optimal torque sharing ratio and the ideal phase current waveform are deduced based on the maximum torque characteristics of two parts of two-segment twisted-rotor DSM, which have 180° electrical angle difference. Then, by sharing the total reference torque to two parts according to optimal torque sharing ratio, the operation principle of the proposed DITC method is derived. Finally, the proposed DITC method is implemented on the 12/8-pole two-segment twisted-rotor DSM drive system. The performance of the proposed DITC method under different commutation angle parameters, different speeds, and reference speed step change are demonstrated through experimental results. The experimental results indicate that the proposed DITC method can suppress the peak current and enhance the torque capability of two-segment twisted-rotor DSM while guaranteeing low torque ripple operation.
4 December 2023 in IEEE Transactions on Industrial Electronics
The doubly salient motor (DSM) is a suitable candidate for the high-speed drive system due to its robust structure and adjustable magnet field. However, the commutation delay at high-speed operation will deteriorate the current performance and thereby degrade the torque capability of the DSM drive system. In this article, the commutation delay compensation (CDC) method based on variable sampling frequency is proposed for the high-speed DSM drive system. First, the production mechanism of commutation delay is analyzed and the commutation delay is classified into two categories. Then, in the proposed CDC method, the angle difference between the sampled rotor position and the given commutation angle is calculated. The sampling frequency is adjusted in real time based on the angle difference and the criterion considering the influence of speed fluctuation. The commutation delay characteristics are analyzed through simulation results. Finally, the proposed CDC method is implemented on a high-speed DSM drive system. The experiment of the proposed CDC method is carried out on the condition of steady-state, different speeds, reference speed step change, and variable load torque. The experimental results indicate that the proposed CDC method can effectively compensate the commutation delay and enhance the torque capability of the high-speed DSM drive system.
18 December 2025 in IEEE Transactions on Transportation Electrification
The effect of the field current and commutation angle parameters on the average torque of a doubly salient electromagnetic motor (DSEM) is highly mutually coupled at high-speed operation. Hence, it is hard for the conventional methods to realize the simultaneous adjustment of field current and commutation angle to fully use the torque capability of the DSEM at high-speed operation. In this article, a commutation angle closed-loop (CAC) based average torque control method is proposed. First, the effect of the field current and commutation angle parameters on the average torque is analyzed. The characteristics of optimal commutation angle parameters are derived, and the CAC method is proposed to adjust the commutation angle parameters by aligning the phase current intersections with phase back electromotive force (EMF) intersections adaptively. Then, the relationship between the field current and average torque is investigated under the proposed CAC method. On this basis, the variable-step perturbation and observation algorithm and average torque control are proposed to adjust the field current by maximizing the average torque. Finally, the proposed CAC-based average torque control method is verified on the high-speed DSEM drive system. The experimental results indicate that the proposed control method can adaptively obtain the optimal commutation angle parameters and field current simultaneously and realize the maximum torque operation of the high-speed DSEM drive system.
15 June 2016 in IEEE Transactions on Automatic Control
This technical note focuses on designing a novel optimal estimation approach for linear discrete-time systems with time-delay and multi-error measurements, inspired by the measurement demands of the Five-hundred-meter Aperture Spherical radio Telescope. Measurement errors from different measurement channels, which are considered equal in many previous estimation methods, are usually negatively correlated with time-delays. Measurements with higher time-delays usually have less errors than the ones with lower delays. Our approach improves the estimation accuracy by decreasing the usage rate of measurements with larger errors. To prove the optimality of the approach in the minimum mean square error sense, a derivation procedure is presented. A numerical example and comparison are also given to demonstrate the feasibility and advantage of the proposed approach.