Chen Xu

Dr. Chen Xu

orcid
I am currently working as Post-Doctoral Fellow with the Scho...

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
25 June 2020 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
Chen XuChen Xu
Chen Xu
ZZZhuoran Zhang
Zhuoran Zhang
LYLi Yu
Li Yu
ZBZhangming Bian
Zhangming Bian
The doubly salient electromagnetic machine (DSEM) is a suitable candidate in many industrial applications due to its simple construction and low manufacture cost. However, the doubly salient structure and the conventional square-wave control method lead to the large torque ripple in the DSEM. In this paper, an improved direct instantaneous torque control (DITC) method is proposed to suppress the inherent torque ripple and enhance the torque capability of the DSEM. The maximum torque characteristics of the DSEM are obtained and analyzed with the finite element method (FEM). Besides, the ideal phase current waveform to realize the low torque ripple is constructed according to the maximum torque characteristics. Then, the operation principle of the proposed DITC method is derived from the maximum torque characteristics. The proposed DITC method is implemented on a prototype of 12/8-pole DSEM drive system. The influence of the commutation angle parameters on the proposed DITC method is analyzed through simulation and experimental results. The simulation and experimental results indicate that the proposed DITC method can realize the smooth torque operation and high torque-ampere ratio simultaneously. Finally, the simulation and experiment under the step reference torque condition are performed to tested the dynamic performance of proposed DITC method.

31 August 2025 in Energy Conversion and Management
Verified
Journal Article
Closed access
WWWen-Qi Wang
Wen-Qi Wang
CWChu-Yao Wang
Chu-Yao Wang
JCJianheng Chen
Jianheng Chen
ZLZe Li
Ze Li
Chen XuChen Xu
Chen Xu
Chi Yan TsoChi Yan Tso
Chi Yan Tso

13 May 2021 in IEEE Transactions on Magnetics
Verified
Journal Article
Closed access
JZJian Zhang
Jian Zhang
YXYiwen Xia
Yiwen Xia
ZZZhuoran Zhang
Zhuoran Zhang
Chen XuChen Xu
Chen Xu
The loss of a doubly salient brushless motor (DSBLM) with rectangular wire armature winding mainly includes ac copper loss, iron loss, and converter loss. The driving mode has a certain influence on motor loss. Therefore, the loss characteristics of a DSBLM with rectangular wire armature winding driven by brushless dc (BLDC) and brushless ac (BLAC) are comparatively studied in this article. First, the magnetic flux density waveforms of armature winding and stator under ideal currents drive are compared, and the waveform changes of ac copper loss and iron loss are analyzed. Second, the effect of pulsewidth modulation (PWM) on motor loss for actual operation in two driving modes is studied. Third, the converter loss of different driving modes is also considered. Finally, the theoretical analysis and simulation results are verified by the experimental results of a DSBLM. In the BLAC driving mode, a DSBLM with rectangular wire armature winding has better loss characteristics.

26 December 2023 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
Chen XuChen Xu
Chen Xu
ZZZhuoran Zhang
Zhuoran Zhang
LYLi Yu
Li Yu
YSYao Sun
Yao Sun
YGYongtao Guan
Yongtao Guan
GHGuangyuan Hu
Guangyuan Hu
The parallel stator poles structure and concentrated field winding configuration of the doubly salient electromagnetic motor (DSEM) lead to the asymmetric three-phase flux paths and thus causing the significant d -axis and q -axis voltage harmonics. In the conventional flux weakening control methods, these d -axis and q -axis voltage harmonics are not considered, which will cause the deviation between the computed voltage and the actual voltage and reduce the dc-link voltage utilization. In this article, an improved flux weakening control method considering the d -axis and q -axis voltage harmonics induced by the asymmetric three-phase flux paths is proposed for the DSEM. First, the asymmetric three-phase flux paths of the DSEM are analyzed in this article. Then, the voltage equation considering the asymmetric three-phase flux paths is derived and verified. The current and voltage constraint are constructed and the reference current curves at different speeds are obtained through the proposed offline method. Finally, the proposed flux weakening control method is implemented on the 12/8-pole DSEM drive system. The experimental results indicate that the proposed flux weakening control method can improve the dc-link voltage utilization, effectively extend the constant torque region, and enhance the output power and torque capability of the DSEM drive system.

12 October 2023 in IEEE Transactions on Transportation Electrification
Verified
Journal Article
Closed access
HLHanqi Li
Hanqi Li
ZZZhuoran Zhang
Zhuoran Zhang
JZJian Zhang
Jian Zhang
Chen XuChen Xu
Chen Xu
WZWeiqiu Zhang
Weiqiu Zhang
Oil cooling technique is one of the important ways to reduce the temperature rise and enhance the power density of aircraft electric machines. However, high viscosity of the oil leads to high flow resistance, which may reduce the efficiency of the hydraulic system and damage the components. This paper conducts research on the flow resistance characteristics of cooling channels. Firstly, considering computational efficiency and accuracy, the influence of mesh type, size, and boundary layers on the cell count and calculation results is compared and summarized. Then, Computational Fluid Dynamics (CFD) models for the series cooling channel and split-flow cooling channel are established. Another split-flow method is explored to optimize the cooling channel. Based on CFD and theoretical formulas, the influence mechanism of channel type and flow rate on flow resistance is revealed. Further, the Heat-pressure ratio ( HPr ) is defined as an indicator to evaluate the heat dissipation capability of cooling structures. Finally, the pressure test models are constructed by 3D printing. The experiments verify the correctness of analysis. The optimization methods can reduce flow resistance by 80.4% and increase Heat Transfer Coefficient by 44% at the same pressure. The HPr can serve as a reference for evaluating cooling structures.

11 October 2025 in Applied Energy
Verified
Journal Article
Closed access
YLYu Lu
Yu Lu
WWWenqi Wang
Wenqi Wang
CWChuyao Wang
Chuyao Wang
ZLZe Li
Ze Li
YZYiying Zhou
Yiying Zhou
CTChi Yan Tso
Chi Yan Tso