1 May 2020 in IEEE Microwave Magazine
To accommodate growing user demand for faster data rates and extensive connectivity, modern wireless communication systems must evolve to support a sharply increasing number of subscribers, all requesting service at the same time. This trend encourages the broad application of multiple input/multiple output (MIMO) systems. In fact, MIMO techniques can increase data rates, coverage of service areas, and communication reliability without additional RFs. In recent proposals for 5G systems, the required separate RF chains in massive MIMO RF front ends can reach up to 256, with bandwidths of up to 800 MHz per RF chain [1], [2]. Massive MIMO is a critical technology that helps significantly in increasing network capacity and spectral efficiency, while reducing wireless network interference, ultimately improving the end-user experience.
9 April 2021 in IEEE Transactions on Microwave Theory and Techniques
In this article, a novel broadband millimeter-wave (mm-wave) front end (FE) based on the asymmetric switch network structure is proposed for multistandard fifth-generation (5G) applications. The asymmetric switch network consists of a bidirectional impedance transformation network and a T-type topology single-pole single-throw (SPST) switch. In the TX-mode, the bidirectional impedance transformation network serves as an output matching network to achieve a continuous-mode Class-F -1 power amplifier (PA) to expand the bandwidth. In the RX-mode, the OFF impedance of the PA can be transformed into a high-impedance region by the bidirectional impedance transformation network. Based on the proposed structure, a broadband mm-wave front end is implemented in the 0.13- μm SiGe BiCMOS process, which occupies 906 μm ×997 μm including pads. In the TX-mode, the -1-dB P sat bandwidth of the FE covers 21-44 GHz with the maximum output power of 18.1-19 dBm and the peak power added efficiency (PAE) of 20.2%-26.8%. In the RX-mode, the FE achieves an 84.6% and -3-dB small-signal gain fractional bandwidth from 20.2 to 49.8 GHz with 38-mW power consumption. It achieves a measured noise figure (NF) of 7.62-11.64 dB over the frequency range of 24-48 GHz. To the best of our knowledge, this is the first FE that covers all the present 5G mm-wave bands without reconfiguration.
21 January 2021 in IEEE Transactions on Circuits and Systems II: Express Briefs
In this brief, a 24-29.5 GHz millimeter-wave (mm-wave) voltage-combined Doherty power amplifier (DPA) based on compact low-loss combiner is proposed for the fifth-generation (5G) applications. By maximizing the use of parasitic parameters in the circuit, a compact low-loss combiner is proposed to achieve the required impedance transformation with only one additional series capacitor. A detailed design procedure is also introduced in the brief. Based on the proposed combiner, a fully integrated Doherty PA is implemented in 0.13- μm SiGe BiCMOS process with a core area of only 0.29 mm 2 . The DPA achieves a 27% -3-dB small-signal gain fractional bandwidth and a 15.9 dB small signal gain at the center frequency of 27 GHz. The -1-dB Psat bandwidth covers 24-29.5 GHz (20% fractional bandwidth), and the maximum output power is 20.8 dBm ± 0.4 dB. From 24 to 29.5 GHz, the designed DPA provides 23.2% to 28.4% power-added efficiency (PAE) at saturated output power, and 18.3% to 21.9% PAE at 6 dB of output power back-off (OPBO).
30 April 2020 in IEEE Microwave and Wireless Components Letters
In this letter, a broadband millimeter-wave (mm-wave) continuous-mode Class-F power amplifier (PA) based on the deembedded transistor model is proposed for the fifth-generation (5G) applications. To design the output matching network at the intrinsic current-generator plane, an S-parameter fitting method is proposed to extract the parasitic parameters of nonpackaged transistors over a wide frequency range. The PA is implemented in the 0.13-μm SiGe BiCMOS process, which occupies only 0.42 mm². By controlling the even and odd harmonics impedance, the PA achieves a 78.2% -3-dB small-signal gain fractional bandwidth from 21.1 to 48.2 GHz. The -1-dB Psat bandwidth covers 21-43 GHz (68.8% fractional bandwidth) and the saturated output powers are 17.2-18.1 dBm. Meanwhile, the designed PA provides a 24.1%-32.1% peak power-added efficiency (PAE) over the band.
9 May 2024 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
This article presents a 24–40-GHz broadband beamforming transmit-receive (T/R) front-end (FE) chip for the next-generation millimeter-wave (mm-wave) communication systems. To achieve multiband coverage in a single beamforming front-end IC, the proposed beamforming chip adopts a unified gain and phase control scheme as well as an asymmetric T/R switch circuit, which simplifies the system design and enables broadband operation in both directions. The vector-modulation-based unified phase and gain control (UPGC) scheme eliminates the standalone variable gain amplifier (VGA) in the front end. The bidirectional impedance transformation T/R switch reduces the insertion loss in the TX path and enables Class-F1 operation to improve the bandwidth and efficiency. Based on the proposed UPGC scheme and T/R switch circuit, a high-performance mm-wave front-end chip is implemented using a 0.13- $\mu $ m SiGe BiCMOS technology. The fabricated front-end chip achieves 12.9–16.9-dBm maximum output power in TX mode, up to 14.3-dB gain and 7.4–9.2-dB noise figure (NF) in RX mode over the frequency range of 24–40 GHz. In both TX and RX modes, the proposed chip achieved less than 0.4-dB rms gain error and 2.0° rms phase error. A four-element dual-band phased array module is designed and tested to evaluate the performance of the proposed chip in the 28- and 38-GHz dual-band phased array.