Letícia Jenisch Rodrigues

Letícia Jenisch Rodrigues

Auto-generated profile, based on publicly available information

Letícia Jenisch Rodrigues

Federal University of Rio Grande do Sul

Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications

1 April 2020 in Journal of Energy Storage
Verified
Journal Article
Closed access
TATiago Haubert Andriotty
Tiago Haubert Andriotty
PSPaulo Smith Schneider
Paulo Smith Schneider
LRLetícia Jenisch Rodrigues
Letícia Jenisch Rodrigues

1 April 2020 in Engenharia Agrícola
Verified
Journal Article
Open access
PDF file
LRLetícia J. Rodrigues
Letícia J. Rodrigues
DBDiego M. Basso
Diego M. Basso
The intermittence of solar radiation, due to continuous rainy or cloudy days, is a limitation of simple and small solar dryers. These conditions often make them impossible to use. By including storage systems (thermal accumulation) and/or auxiliary energy sources, drying processes or dehydration can be conducted continuously, even during periods of low insolation. Therefore, the present work simulates and evaluates the thermal and energetic behavior of a hybrid system for heating the air that is directed to the dehydration chamber of a solar food dryer. The software selected for the simulation was TRNSYS. The simulated hybrid system consists of a flat plate solar collector and an arrangement of electrical resistors that guarantee the entry of air, at a constant temperature, into the dehydration chamber. The target temperature selected is 70 oC, and the absence of food products in the chamber is assumed. An arrangement with four electric resistors totaling 1900 W, with three different powers of 1000 W, 500 W, and 200 W proved adequate to guarantee the entrance of air at a constant temperature when considering the climatic conditions of a city in the South of Brazil.

1 March 2013 in Progress in Nuclear Energy
Verified
Journal Article
Closed access
LRLetícia Jenisch Rodrigues
Letícia Jenisch Rodrigues
SLSérgio Q. Bogado Leite
Sérgio Q. Bogado Leite
MVMarco Tullio de Vilhena
Marco Tullio de Vilhena

1 April 2016 in Defect and Diffusion Forum
Verified
Journal Article
Closed access
PDF file
TATiago Haubert Andriotty
Tiago Haubert Andriotty
LRLetícia J. Rodrigues
Letícia J. Rodrigues
LRLuiz Alberto Oliveira Rocha
Luiz Alberto Oliveira Rocha
PSPaulo Smith Schneider
Paulo Smith Schneider
This study is focused on the optimization of a sensible thermal storage system subjected to a cyclic energy source. The objective is to minimize the system heat storage mass and its geometry to guarantee its operation within an admissible temperature range. The storage medium is modeled as a Lumped system and the working fluid by a non-capacitive energy balance. The storage medium is composed of an array of parallel flat plates submitted to an air stream. The optimization is based on an exhaustive search method. It is observed that the minimum heat storage mass is proportional to the mass airflow rate. An optimal relationship between the superficial heat transfer rate and the fluid flow inertia, given by the dimensionless parameter NTU, is found to be constant (4.03) and independent in respect to the mass flow rate. The system time constant was invariable (3,230 s) for the optimal relationship between the interface heat transfer rate and the system inertia.

1 September 2008 in Kerntechnik
Verified
Journal Article
Closed access
LRL. Jenisch Rodrigues
L. Jenisch Rodrigues
SLS. Q. Bogado Leite
S. Q. Bogado Leite
MVM. T. de Vilhena
M. T. de Vilhena
In the present work, the WIMSD code routine PIJM is modified to compute deterministic Dancoff factors by the collision probability definition in general arrangements of partially absorbing fuel rods. Collision probabilities are calculated by an efficient integration scheme of the third-order Bickley functions, which considers each cell region separately. The effectiveness of the method is assessed by comparing grey Dancoff factors as calculated by PIJM, with those available in the literature by the Monte Carlo method, for the irregular geometry of the Canadian CANDU and CANFLEX assemblies. Dancoff factors at several different fuel pin positions are found in very good agreement with the literature results.