Hassanein I. Khalaf

Hassanein I. Khalaf

Auto-generated profile, based on publicly available information

Hassanein I. Khalaf

Mechanical Department, Engineering College, University of Basrah, Basrah 61004, Iraq

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 March 2022 in Materials
Verified
Journal Article
Open access
PDF file
HKHassanein I. Khalaf
Hassanein I. Khalaf
Raheem Al-SaburRaheem Al-Sabur
Raheem Al-Sabur
Mahmoud E. AbdullahMahmoud E. Abdullah
Mahmoud E. Abdullah
AKAndrzej Kubit
Andrzej Kubit
HDHamed Aghajani Derazkola
Hamed Aghajani Derazkola
This article aims to study water-cooling effects on residual stress friction stir welding (FSW) of AA6068-T6 aluminum alloy. For this reason, the FSW and submerged FSW processes are simulated by computational fluid dynamic (CFD) method to study heat generation. The increment hole drilling technique was used to measure the residual stress of welded samples. The simulation results show that materials softening during the FSW process are more than submerged. This phenomenon caused the residual stress of the joint line in the submerged case to be lower than in the regular FSW joint. On the other hand, the results revealed that the maximum residual stresses in both cases are below the yielding strength of the AA6068-T6 aluminum alloy. The results indicated that the residual stress along the longitudinal direction of the joint line is much larger than the transverse direction in both samples.

31 October 2022 in Polymers
Verified
Journal Article
Open access
PDF file
HKHassanein I. Khalaf
Hassanein I. Khalaf
Raheem Al-SaburRaheem Al-Sabur
Raheem Al-Sabur
Murat DemiralMurat Demiral
Murat Demiral
JTJacek Tomków
Jacek Tomków
JLJerzy Labanowski
Jerzy Labanowski
HDHamed Aghajani Derazkola
Hamed Aghajani Derazkola
Friction stir welding (FSW) of polymeric materials has recently attracted significant attention. Herein, we present the effect of the tool pin profile on the FSW of high-density polyethylene (HDPE) joints through joint experimental analysis and thermomechanical simulations. For analysis of pin profile effects on the thermomechanical properties of HDPE joints, frustum (FPT), cubic (CPT), and triangular (TPT) pin shapes were selected in this study. This research investigated the heat generation of the parts of the different tools as well as heat flux (internal and surface). The results revealed that the heat generation in pins with more edges (cubic (96 °C) and triangular (94 °C)) was greater than in pins with a smooth shape (frustum (91 °C)). The higher heat generation caused the heat flux on the surface of the HDPE from the cubic pin profile to be greater than for other joints. Due to the properties of HDPE, higher heat generation caused higher material velocity in the stirring zone, where the velocity of the materials in TPT, CPT, and FPT pins were 0.41 m/s, 0.42 m/s, and 0.4 m/s, respectively. The simulation results show sharp-edged pins, such as triangular and cubic, lead to over-stirring action and internal voids formed along the joint line. Furthermore, the simulation results indicated that the size of the stirred zones (SZs) of the FPT, TPT, and CPT samples were 17 mm2, 19 mm2, and 21 mm2, respectively, which is around three times the corresponding values in the HAZ.

14 June 2022 in Materials
Verified
Journal Article
Open access
PDF file
Raheem Al-SaburRaheem Al-Sabur
Raheem Al-Sabur
HKHassanein I. Khalaf
Hassanein I. Khalaf
AŚAleksandra Świerczyńska
Aleksandra Świerczyńska
GRGrzegorz Rogalski
Grzegorz Rogalski
HAHesamoddin A-Derazkola
Hesamoddin A-Derazkola
In this study, the effects of the traverse and rotational velocities of the noncontact shoulder tool on the heat generation and heated flux during the friction stir joining of high-density polyamide 6 (PA6) polymer were investigated. The computational fluid dynamics (CFD) method was employed to simulate the thermomechanical phenomena during the friction stir joining (FSJ) process of PA6. A developed model was used to consider the void formation and thermochemical properties of PA6. The surface and internal heat flow, material flow, and geometry of the joint were simulated, and an experimental study evaluated the simulation results. The simulation results indicated that the stir zone formed was smaller than regular joints with a noncontact shoulder tool. Despite the polymer’s traditional FSJ, heat generation and material flow do not differ significantly between advancing and retreating sides. On the other hand, the surface flow is not formed, and the surface temperature gradient is in a narrow line behind the tool. The material velocity increased at higher rotational speed and lower transverse velocity and in the stir zone with more giant geometry forms. The maximum generated heat was 204 °C, and the maximum material velocity was predicted at 0.44 m/s in the stir zone, achieved at 440 rpm and 40 mm/min tool velocities.

6 April 2023 in Materials
Verified
Journal Article
Open access
PDF file
Raheem Al-SaburRaheem Al-Sabur
Raheem Al-Sabur
AKAndrzej Kubit
Andrzej Kubit
HKHassanein I. Khalaf
Hassanein I. Khalaf
WJWojciech Jurczak
Wojciech Jurczak
Andrzej DzierwaAndrzej Dzierwa
Andrzej Dzierwa
MKMarcin Korzeniowski
Marcin Korzeniowski
Studying roughness parameters and the topography of stiffening ribs in composite sandwich structures is important for understanding these materials’ surface quality and mechanical properties. The roughness parameters describe the micro-geometry of the surface, including the average height deviation, roughness depth, and waviness. The topography of the surface refers to the spatial arrangement and distribution of features such as bumps, ridges, and valleys. The study investigated the roughness parameters under three scenarios based on two SPIF process parameters: tool rotational speed(N) and feed rate (f). The vertical step was held constant at 0.4 mm across all scenarios. In scenario A, the process parameters were set at f = 300 mm/min and n = 300 rpm; in scenario B, f = 1500 mm/min and n = 3000 rpm; and in scenario C, f = 1500 mm/min and n = 300 rpm. The experimental research topography analyses revealed that the surface roughness of the stiffened ribs was highly dependent on the SPIF process parameters. The highest feed rate and tool rotational speed produced the smoothest surface texture with the lowest maximum height (Sz) value. In contrast, the lowest feed rate and tool rotational speed resulted in a rougher surface texture with a higher maximum height (Sz) value. Furthermore, the contour plots generated from the topography analyses provided a good visual representation of the surface texture and roughness, allowing for a more comprehensive analysis of the SPIF process parameters. This study emphasizes optimizing the SPIF process parameters to achieve the desired surface quality and texture of stiffened ribs formed in Litecor® panel sheets.

6 May 2021 in The European Physical Journal Plus
Verified
Journal Article
Closed access
PDF file
HKHassanein I. Khalaf
Hassanein I. Khalaf
KSKhalid Baker Saleem
Khalid Baker Saleem
Khaled Al-FarhanyKhaled Al-Farhany
Khaled Al-Farhany
WAWael Al-Kouz
Wael Al-Kouz

10 April 2024 in Materials
Verified
Journal Article
Open access
PDF file
HKHassanein I. Khalaf
Hassanein I. Khalaf
Raheem Al-SaburRaheem Al-Sabur
Raheem Al-Sabur
AKAndrzej Kubit
Andrzej Kubit
ŁŚŁukasz Święch
Łukasz Święch
Krzysztof ZabaKrzysztof Zaba
Krzysztof Zaba
VNVít Novák
Vít Novák
The aluminum strength-to-weight ratio has become a highly significant factor in industrial applications. Placing stiffening ribs along the surface can significantly improve the panel’s resistance to bending and compression in aluminum alloys. This study used single-point incremental forming (SPIF) to fabricate stiffening ribs for 1 mm and 3 mm thick aluminum alloy EN AW-2024-T3 sheets. A universal compression machine was used to investigate sheet deformation. The resulting deformation was examined using non-contact digital image correlation (DIC) based on several high-resolution cameras. The results showed that deformation progressively escalated from the edges toward the center, and the highest buckling values were confined within the non-strengthened area. Specimens with a larger thickness (3 mm) showed better effectiveness against buckling and bending for each applied load: 8 kN or 10 kN. Additionally, the displacement from the sheet surface decreased by 60% for sheets 3 mm thick and by half for sheets 1 mm thick, which indicated that thicker sheets could resist deformation better.