Juan Luis Corral

Juan Luis Corral

Auto-generated profile, based on publicly available information

Juan Luis Corral

Instituto Universitario de Tecnologa Nanofotnica, Universitat Politcnica de Valncia, Valencia, Spain

Research Focus & Metrics

Academic Career Length

25Years (2002-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 July 2018 in Optics Express
Verified
Journal Article
Open access
PDF file
David Garcia-RodriguezDavid Garcia-Rodriguez
David Garcia-Rodriguez
JCJuan L. Corral
Juan L. Corral
AGAmadeu Griol
Amadeu Griol
RLRoberto Llorente
Roberto Llorente
In this paper, we evaluate by means of simulation and experimentally the simultaneous coupling of the LP01x-LP11ax fiber modes and the TE0-TE1 nanophotonic SOI waveguide modes using a grating coupler for a two-mode fiber at 1550 nm. Both the grating width (ranging from 10 µm to 15 µm) and the grating vertical profile have been considered in the design procedure. The optimum design (14 µm width and 609 nm grating period) has been selected in terms of coupling efficiency (both LP01x-TE0 and LP11ax-TE1), compactness and tolerance to lateral misalignments between fiber and coupler. The LP01x-TE0 and LP11ax-TE1 modes achieved coupling efficiencies of 49% and 45%, respectively.

9 July 2018 in Optics Express
Verified
Journal Article
Open access
PDF file
JBJulián S. Bruno
Julián S. Bruno
VAVicenç Almenar
Vicenç Almenar
JVJavier Valls
Javier Valls
JCJuan L. Corral
Juan L. Corral
This paper presents the hardware architecture of an OFDM receiver suitable for optical communications. The receiver has been implemented in an FPGA device and used to demonstrate experimentally an optical OFDM transmission in a passive optical link with a directly modulated DFB laser and DAC/ADC at 5 GS/s. A bit rate of 20.37 Gb/s is achieved using an OFDM signal with subcarrier modulation format up to 512-QAM, it has been successfully transmitted over 10 km SSMF with a spectral efficiency of 8.38 bit/s/Hz.

14 February 2022 in Journal of Lightwave Technology
Verified
Journal Article
Closed access
PSPau Salvador
Pau Salvador
JVJavier Valls
Javier Valls
JCJuan Luis Corral
Juan Luis Corral
VAVicenç Almenar
Vicenç Almenar
MSMªJosé Canet Subiela
MªJosé Canet Subiela
The widespread deployment of LEDs for illumination purposes has open the door to the use of these devices for visible light communications (VLC). Most lighting fixtures are mounted with phosphor-based white LEDs, and a driver connected to the LED is also required for VLC. This paper shows that the parasitic effects introduced by this setup change the frequency response of the intrinsic LED. A linear model to characterize the whole setup is proposed, as well as a methodology to extract its parameters. This methodology allows the designer to characterize the frequency response of LEDs without the additional difficulty of knowing the specific parasitic components introduced by the setup. The proposed model offers an accurate estimation of the slope of the LED frequency response in order to broaden the frequency range in which the model is useful to characterize and simulate VLC links. This was corroborated with the characterization of three commercial white LEDs whose measured and modeled frequency responses matched perfectly.

22 August 2005 in IEEE Photonics Technology Letters
Verified
Journal Article
Closed access
MPM.A. Piqueras
M.A. Piqueras
BVB. Vidal
B. Vidal
JCJ.L. Corral
J.L. Corral
VPV. Polo
V. Polo
AMAlejandro Martinez
Alejandro Martinez
JMJ. Marti
J. Marti
In this letter, a novel quadrature photonic vector modulator architecture is proposed. An electrical quadrature-modulated signal at microwave/millimeter-wave frequencies is generated from its corresponding base-band in-phase (I) and quadrature (Q) components. In the proposed scheme, no electrical devices apart from the electrical tone oscillator are needed in the generation process and, therefore, high data rates at high electrical frequencies can be obtained. In addition, the hardware requirements are reduced when compared to previously proposed architectures so a highly compact low-cost architecture can be implemented. Experimental results demonstrate the feasibility of the architecture.

14 July 2022 in Journal of Lightwave Technology
Verified
Journal Article
Closed access
PSPau Salvador
Pau Salvador
JVJavier Valls
Javier Valls
MSMªJosé Canet Subiela
MªJosé Canet Subiela
VAVicenç Almenar
Vicenç Almenar
JCJuan Luis Corral
Juan Luis Corral
LED lamps have become the predominant technology for lighting thanks to their low power consumption. Recently, the joint use of these devices for lighting and data transmission has aroused interest in the research community as a future green communication technology. During this time, many of the advances developed in this area have been demonstrated with experimental setups using LED drivers based on bias-T, thanks to their ease to combine signal modulation and LED bias. This article discusses the impact of the output impedance of the bias-T driver and the driver-LED connection parasitics on the performance and energy efficiency of the VLC system. It is concluded that the output impedance of the driver not only affects energy efficiency but also modifies the frequency response and, therefore, the LED's capacity to be modulated. A low output impedance driver is shown to offer a substantial improvement in the energy efficiency of the VLC driver.

17 May 2018 in Optics Letters
Verified
Journal Article
Closed access
PDF file
David Garcia-RodriguezDavid Garcia-Rodriguez
David Garcia-Rodriguez
JCJuan L. Corral
Juan L. Corral
RLRoberto Llorente
Roberto Llorente
The supermode analysis of asymmetrical directional couplers (ADC) based on SOI technology for strip and ridge structures at 1550 nm is herein reported, targeting to reduce ADC device fabrication requirements. The reported analysis based on supermodes permits us to assess the sensitivity of the ADC coupling efficiency by calculating the index difference between even and odd supermodes. Optimum designs have been found for 100 and 400 nm gaps, respectively, capable of converting and (de) multiplexing both TE0 and TE1 modes taking into account the width, gap, height, and slab thickness variations produced with respect to the nominal design.