G. G. Osinovyy

G. G. Osinovyy

Auto-generated profile, based on publicly available information

G. G. Osinovyy

Yuzhnoye State Design Office, Dnipro, Ukraine

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 October 2024 in Kosmìčna nauka ì tehnologìâ
Verified
Journal Article
Closed access
YYYuzhnoye State Design Office named after M. K. Yangel
Yuzhnoye State Design Office named after M. K. Yangel
VNVolodymyr Nadtoka
Volodymyr Nadtoka
IHI. O. Husarova
I. O. Husarova
MKM. V. Kraiev
M. V. Kraiev
АBА. Yu. Borysenko
А. Yu. Borysenko
GOG. G. Osinovyy
G. G. Osinovyy
An investigation was done for heat-resistant coatings from Ni-Cr and Fe-Ni-Cr alloys, produced by vacuum arc deposition with cathodes from nichrome alloy ХН78Т and steel 12Х18Н10Т. The microstructural analysis of the studied coatings applied by vacuum arc deposition with different amounts of reactive gas (nitrogen) in a deposition chamber showed the presence of two phases: a matrix and the distributed particles of liquid phase of various sizes and shapes. Vacuum arc deposition at a cathode arc current of 55 A for Ni-Cr and 82 A for Fe-Ni-Cr coatings, a cathode arc voltage of 28 to 32 V, an underlayer temperature of 490±30 оС, and no nitrogen in the chamber gives coatings with no apparent orientation of crystallites and a microhardness reaching 330 to 374 HV. The diffusion mobility of atoms decreases at a higher nitrogen pressure, which results in a coarse-crystal, porous-columnar structure of coatings with high porosity, a varying volume, and a rough surface. The influence of nitrogen pressure in a chamber on the strength of coatings was evaluated by their microhardness. A nitrogen pressure gain up to 0.13 Pa results in the increased microhardness of both coating systems, and the further growth in pressure has almost no effect on microhardness. It was discovered that a nitrogen pressure of 0.13 Pa gives the optimum combination of a coating’s strength and continuous structure with no pores and apparent columnar crystallites. Alloys from Ni-Cr with 80 % Ni are among the most heat-resistant industrial materials with a maximum operating temperature of up to 1200 оС. However, they are expensive, which makes Fe-Ni-Cr alloys more attractive, providing their heat resistance is sufficient for the operating temperature range. Therefore, it is reasonable to conduct further research on both Ni-Cr and Fe-Ni-Cr coatings to develop a deposition technology that can provide the required performance parameters. Controlling nitrogen pressure makes it possible to adjust the structure and properties of the coating during deposition.

27 January 2026 in Kosmičeskaâ tehnika. Raketnoe vooruženie
Verified
Journal Article
Closed access
APA. A. Pustovharov
A. A. Pustovharov
IHI. O. Husarova
I. O. Husarova
KKK. V. Kozis
K. V. Kozis
YLYa. A. Lysenko
Ya. A. Lysenko
HOH. H. Osinovyy
H. H. Osinovyy
The 21st century started with changes in hopes and expectations for space exploration. Plans are being announced to move from researching and studying the solar system to colonizing it. The primary object of attention is the Earth’s natural satellite. A return to the Moon is expected in the near future, and various countries are already planning short-term crewed expeditions to the Moon. A gradual establishment of permanent human presence on the Moon is supposed, for which lunar bases will be created. One of the most essential tasks in exploring the Moon will be to ensure the reliable transportation of people and cargo between Earth and the Moon. The intensity of spacecraft fl ights will increase signifi cantly after the start of lunar base construction, remaining high in subsequent stages. Therefore, it can be expected that spaceports will become essential components of lunar bases. In addition to prepared sites, spaceports must have the necessary equipment and resources. The creation of a spaceport on the Moon has its own peculiarities, which are discussed in this article. The article examines the specifi city of spaceport construction on the Moon, considering the unusual nature of this task, and makes a brief analysis of modern approaches to accomplishing it. The article supposes the potential location of the spaceport, outlines the possible impact of lunar surface relief on spaceport construction, and identifi es factors of priority concern. The fi rst approximation provides the principal quantitative and qualitative indicators characterizing the spacecraft landing process. Recommendations are given regarding selecting the shape and size of landing pads for spacecraft. A possible structural diagram of a lunar spaceport has been developed, with a list of the primary components and equipment. The article also identifi es limitations that need to be taken into account and indicates various factors that will infl uence the design of the spaceport and, therefore, need to be considered. The work carried out may serve as a theoretical basis for the further development of the lunar base concept.

29 May 2026 in Physicochemical Mechanics of Materials
Verified
Journal Article
Closed access
IHI. O. Husarova
I. O. Husarova
OGO. M. Grigoriev
O. M. Grigoriev
DVD. V. Vedel
D. V. Vedel
MKM. V. Kraiev
M. V. Kraiev
TMT. A. Manko
T. A. Manko
GOG. G. Osinovyy
G. G. Osinovyy
А comparative analysis of heat-shielding coatings of rocket and space technology is carried out, and the prospects for the use of ultrahigh-temperature ceramics as heat-resis¬tant coatings for elements of hypersonic aircraft, in particular, nose сone and wing edges, are considered. A coating based on the ZrB2-MoSi2 ceramic system was obtained by vacuum-arc deposition on a carbon substrate. It is shown that the formed coating has a homogeneous structure, low oxygen content (< 2 mass%), and satis¬factory adhesion to the substrate, which is associated with close coefficients of thermal expansion of the compo¬nents. The technology of vacuum ion-plasma spraying of ZrB2-MoSi2 coatings is promi¬sing for increasing the temperature resistance of carbon structures under conditions of short-term thermal load in an oxidizing environment at extremely high temperatures.