Eduardo Bellini Ferreira

Eduardo Bellini Ferreira

Auto-generated profile, based on publicly available information

Eduardo Bellini Ferreira

Department of Materials Engineering São Carlos Engineering School University of São Paulo (USP) São Carlos Brazil

Research Focus & Metrics

Academic Career Length

23Years (2004-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2005 in Journal of Non-Crystalline Solids
Verified
Journal Article
Open access
MNMarcio Nascimento
Marcio Nascimento
LSLuciana A. Souza
Luciana A. Souza
EFEduardo B. Ferreira
Eduardo B. Ferreira
EZEdgar Zanotto
Edgar Zanotto
Glass-forming ability (GFA) is the easiness to vitrify a liquid on cooling, while glass stability (GS) is the glass resistance against devitrification on heating; but it is questionable if there is any direct relationship between these two parameters. Therefore, to test this possibility, we assess and compare GFA and several GS parameters through quantitative criteria. GFA and GS were calculated for six stoichiometric glass forming oxides that only present surface (heterogeneous) crystallization in laboratory time scales: GeO 2 , Na 2 O · 2SiO 2 , PbO · SiO 2 , CaO · Al 2 O 3 · 2SiO 2 , CaO · MgO · 2SiO 2 and 2MgO · 2Al 2 O 3 · 5SiO 2 ; plus Li 2 O · 2SiO 2 and Li 2 O · 2B 2 O 3 that, in addition to surface nucleation, also present homogeneous (internal) crystallization. We gauge GFA by the critical cooling rate, q cr , which was calculated from an estimated number of heterogeneous nucleation sites per unit surface, N s , and from experimental crystal growth rates, u ( T ), assuming a detectable surface crystallized fraction X c = 0.001. We define GS parameters by fourteen different combinations of the following characteristic differential thermal analysis (DTA) or differential scanning calorimetry (DSC) temperatures: the glass transition temperature ( T g ), the onset crystallization temperature on heating ( T x h ) , the peak crystallization temperature on heating ( T c h ) , and the melting point ( T m ). To obtain the experimental GS parameters for each glass we carried out DSC runs using coarse and fine powders, and completed the necessary data with literature values for T m . The results for fine and coarse particles were quite similar. Most of the GS parameters that consist of three characteristic DSC temperatures show excellent correlation with GFA, however, rather poor correlations were observed for parameters that use only two characteristic temperatures. We thus demonstrated that certain, but not all GS parameters can be used to infer GFA. IDT C250 C290 C2865 G160 G183 PACS 64.70.Dv 81.10.Aj 1 Introduction There is now consensus that any material can vitrify if cooled from the molten state to the glass transition temperature, T g , at a rate fast enough to prevent crystallization. The slowest a material can be cooled down to T g without crystallization the easiest it is vitrified, and this property is denominated glass forming ability (GFA). A maximum allowed fraction of crystals, X c , usually taken between 0.1% and 0.0001%, is conventionally assumed to classify a material as glassy. One can thus define a critical cooling rate , q cr , to avoid a crystalline fraction higher than X c on cooling a liquid. Therefore, q cr gauges GFA. However, it is quite difficult to accurately measure q cr and the complexity increases for reluctant glass formers that require very high cooling rates. If one could devise indirect ways to estimate GFA would then avoid exhaustive laboratory investigations, and this is thus a key step for efficient development of new glasses and glass-ceramics. On the other hand, once a glass is made, for instance by fast quenching a melt, its stability against crystallization can be easily investigated. The resistance of a given glass against crystallization upon reheating defines glass stability (GS). GS is typically derived from characteristic temperatures that are determined from simple non-isothermal analyses, such as DTA or DSC. It is thus desirable to know how one can estimate GFA from GS measurements. However, the definitions of GS are somewhat arbitrary, only seldom have been rigorously tested and, as we will summarize below, it is controversial if there is any straightforward relationship between GFA and GS. In this work, we experimentally test the existence of possible correlations between precisely calculated critical cooling rates (GFA) and fourteen ways to characterize GS using DSC. We use eight stoichiometric glasses: GeO 2 (G), Na 2 O · 2SiO 2 (NS 2 ), CaO · MgO · 2SiO 2 (CMS 2 ), PbO · SiO 2 (PS), 2MgO · 2Al 2 O 3 · 5SiO 2 (M 2 A 2 S 5 ) and CaO · Al 2 O 3 · 2SiO 2 (CAS 2 ), which only show heterogeneous (surface) nucleation; plus Li 2 O · 2SiO 2 (LS 2 ) and Li 2 O · 2B 2 O 3 (LB 2 ) that also show homogeneous (internal) nucleation in addition to predominant surface nucleation. Therefore, the paper’s objective is to systematically verify possible relationships between GFA and GS parameters for glasses that crystallize via the most common nucleation mechanism, i.e. surface (heterogeneous) nucleation. 1.1 Literature review 1.1.1 Glass forming ability A variety of theories have been proposed to understand why some systems easily vitrify while others do not [1,2] . Ultimately, a high glass forming ability is associated with slow crystallization rates. Uhlmann [3] was one of the first to use the concept of crystallization kinetics controlling glass formation. His method refers to TTT (time–temperature–transformation) diagrams, which are temperature versus time graphs showing curves that correspond to specified fractions of transformed phase. A curve in a TTT diagram shows how one can set a thermal treatment to achieve a given fraction of transformed phase. To vitrify a liquid by cooling, the crystallized fraction of interest is normally the smallest detectable, usually assumed to be 10 −2 –10 −6 . A ‘nose’ arises in the TTT diagrams at a temperature T n and time t n where the rate of transformation is the fastest. According to the nose method , the critical cooling rate for glass formation, q cr n , is given by (1) q cr n = T m - T n t n . However, critical cooling rates calculated by the nose method are typically one order of magnitude greater than experimentally determined values [4] . Thus, this method can only be used to estimate relative critical cooling rates...

1 November 2009 in Journal of Non-Crystalline Solids
Verified
Journal Article
Closed access
ACAna Milena Cruz
Ana Milena Cruz
EFEduardo Bellini Ferreira
Eduardo Bellini Ferreira
ARAna Candida M. Rodrigues
Ana Candida M. Rodrigues

12 August 2010 in Journal of the American Ceramic Society
Verified
Journal Article
Closed access
PDF file
EFEduardo Bellini Ferreira
Eduardo Bellini Ferreira
MLMoysés L. Lima
Moysés L. Lima
EZEdgar Zanotto
Edgar Zanotto

8 November 2004 in The Journal of Chemical Physics
Verified
Journal Article
Closed access
MNMarcio Nascimento
Marcio Nascimento
EFEduardo Bellini Ferreira
Eduardo Bellini Ferreira
EZEdgar Zanotto
Edgar Zanotto
Extensive data on the viscosity, covering 15 orders of magnitude, and crystal growth rate, covering seven orders of magnitude, of liquid diopside (CaO.MgO.2SiO(2)) were collected in a wide range of undercoolings from 1.10T(g) to 0.99T(m) (T(g) is the glass transition temperature and T(m) the melting point). The raw growth rate data were corrected for the increased interfacial temperature produced by the heat released during crystallization. A detailed analysis confirms that growth mediated by screw dislocations reasonably explain the experimental data in these wide ranges of temperatures and growth rates. Effective diffusion coefficients were calculated from crystal growth rates and from viscosity, and were then compared with measured self-diffusion coefficients of silicon and oxygen in diopside melt. The results show that oxygen and silicon control the diffusion dynamics involved in crystal growth and viscous flow. This study not only unveils the transport mechanism in this complex liquid, but also validates the use of viscosity (through the Stokes-Einstein or the Eyring equations) to account for the kinetic term of the crystal growth expression in a wide range of temperatures.

1 January 2021 in Materials Research
Verified
Journal Article
Open access
ABAlexandre Lopes Borges
Alexandre Lopes Borges
SSSilvete Mari Soares
Silvete Mari Soares
TFTaís Freitas
Taís Freitas
AJAdalberto de Oliveira Júnior
Adalberto de Oliveira Júnior
EFEduardo Bellini Ferreira
Eduardo Bellini Ferreira
FFFernanda Ferreira
Fernanda Ferreira

1 July 2007 in Journal of Non-Crystalline Solids
Verified
Journal Article
Closed access
Haroldo Cavalcanti  PintoHaroldo Cavalcanti Pinto
Haroldo Cavalcanti Pinto
LIL. Ito
L. Ito
MCMurilo Camuri Crovace
Murilo Camuri Crovace
EFE.B. Ferreira
E.B. Ferreira
FFF. Fauth
F. Fauth
APA.R. Pyzalla
A.R. Pyzalla