Shibo Zhang

Shibo Zhang

Auto-generated profile, based on publicly available information

Shibo Zhang

Multifield Ultrasonic Equipment (Jiangxi) Co., Ltd., Fuzhou 344000, China; ShenZhen Vibrosurgery Instrument Co., Ltd., Shenzhen 518000, China

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 February 2023 in Ultrasonics
Verified
Journal Article
Closed access
SZShibo Zhang
Shibo Zhang
ZCZhirui Chen
Zhirui Chen
HWHanqiang Wu
Hanqiang Wu
GLGengzhuo Li
Gengzhuo Li
YWYongbo Wu
Yongbo Wu

1 January 2021 in Ultrasonics
Verified
Journal Article
Closed access
SZShibo Zhang
Shibo Zhang
YGYifan Guo
Yifan Guo
ZCZhenchang Chen
Zhenchang Chen
GLGengzhuo Li
Gengzhuo Li
QGQiongyu Guo
Qiongyu Guo
JZJiang Zeng
Jiang Zeng

1 November 2021 in Sensors and Actuators A: Physical
Verified
Journal Article
Closed access
SZShibo Zhang
Shibo Zhang
ZCZhirui Chen
Zhirui Chen
GLGengzhuo Li
Gengzhuo Li
YWYongbo Wu
Yongbo Wu

13 September 2021 in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
Verified
Journal Article
Closed access
PDF file
SZShibo Zhang
Shibo Zhang
YLYang Li
Yang Li
SLSisi Li
Sisi Li
YWYongbo Wu
Yongbo Wu
JZJiang Zeng
Jiang Zeng
In the field of power ultrasound, Langevin ultrasonic transducers (LUTs) usually operate at a large displacements output power by applying high voltages. However, empirically, a LUT exhibits nonlinearities such as amplitude jumping and peak hysteresis for high voltages in actual operations. The nonlinearities would reduce the efficiency and output accuracy of an LUT. In this research, the burst-mode method was used to measure the longitudinal vibration velocity of the LUT, which gradually decreased with time after the excitation voltage was turned off. The equivalent mechanical losses and equivalent spring constants were determined using the velocity attenuation rate and resonant frequency and they were found to be the linear functions of velocity, helping to develop a novel nonlinear model. This model contained two quadratic nonlinear terms based on the linear model. Furthermore, the developed nonlinear model was analyzed using the Lagrangian method as well as the multiscale method, which confirmed that the model was effective in describing the nonlinear behavior. It was also found that the frequency-amplitude curve bent when the nonlinear term was taken into account, which resembled the nonlinear phenomenon tested experimentally. From a physical point of view, this bending was meaningful because it led to the formation of multi-valued response regions with jumping phenomena. Additionally, according to the obtained results, the maximum value of the system response was independent of the degree of nonlinearity of the system.

12 September 2023 in Lubricants
Verified
Journal Article
Open access
PDF file
HWHanqiang Wu
Hanqiang Wu
XYXimin Ye
Ximin Ye
ZCZhuo Chen
Zhuo Chen
SZShibo Zhang
Shibo Zhang
JZJiang Zeng
Jiang Zeng
YWYongbo Wu
Yongbo Wu
To reduce wheel loading caused by chip adhesion in the grinding of titanium alloys, a new method named ultrasonic-assisted plasma oxidation modification grinding is suggested. The processing principle was introduced in this research, and based on that, the experimental apparatus was established. Then, the surface and cross-sectional morphologies of a workpiece with an oxide layer were characterized, followed by the detection of its microhardness and surface composition. On this basis, in the absence and presence of the oxide layer, the dynamic changes in wheel loading on the grinding wheel surface and the evolution behavior of chip adhesion on the grains were both investigated after gradually increasing the grinding passes. Finally, the effects of wheel loading on the ground surface morphologies were analyzed. The results showed that the oxide layer with low microhardness was mainly composed of TiO2 and Al2O3. Moreover, with an increase in grinding passes, the overall occupied area of chip adhesion on the grinding wheel surface increased proportionally in the absence of the oxide layer, which finally caused severe wheel loading. Conversely, yet at almost the same rate, the overall occupied area of chip adhesion increased after remaining comparatively unchanged in a short range of grinding passes in the presence of the oxide layer, which effectively inhibited the wheel loading. Compared with the ground surface obtained without an oxide layer, the generation of plastic-stacking was significantly restrained with the assistance of the oxide layer, thereby improving the ground surface quality.

26 April 2018 in Theoretical and Computational Fluid Dynamics
Verified
Journal Article
Closed access
PDF file
SWShuai Wang
Shuai Wang
LLLi LIU
Li LIU
SZShi-Bo Zhang
Shi-Bo Zhang
FWFengbo Wen
Fengbo Wen
XZXun Zhou
Xun Zhou