30 January 2018 in Journal of Fluids Engineering
Based on computational fluid dynamics and the finite volume method, water droplet erosion in the last stage of an industrial steam turbine was researched and the trajectories of the water droplets were traced by using the Lagrange method. Under steady conditions, the influence of variant bowed vane designs was compared based on the distribution and movement trends of the secondary water droplets. In addition, the effects of the bowed blades on water movement at the vane surfaces and their impact areas and intensity on the blades were analyzed. The results showed that: (1) a negatively bowed blade can reduce the speed of the secondary water droplets at the mid span of the blade, which are also effective for water droplets on the surface of the vanes and (2) a negatively bowed blade improves the speed of the secondary droplets on the end walls of vanes, which is advantageous to the secondary droplets through blade passage and reduction of secondary droplet impulse on the blades.
1 August 2023 in Physics of Fluids
The prediction of compressor cascade loss is a crucial aspect of compressor design. Flow separation is an important flow structure and the main source of loss in subsonic cascades. In order to capture the flow separation and accurately evaluate flow loss, a data-driven quasi-three-dimensional (quasi-3D) subsonic compressor cascade loss prediction model based on bidirectional long short-term memory (BiLSTM) and multi-head self-attention is proposed. The model contains four sub-models to predict the pressure, temperature, axial velocity, and total pressure loss coefficient in two-dimensional slices along the axial direction, using Mach number, curved blade angle, solidity, camber angle, and incidence as inputs, respectively. For the purpose of adapting to cascade geometrical change, geometric reformulation is adopted before the model training. The model is trained and tested by validated computational fluid dynamics results, which contain symmetric separation and asymmetric separation samples. It is proved that the model is able to accurately predict flow parameters value in each slice. Then, four typical cases are mainly discussed, which shows that the model can effectively capture the characteristics of flow separation formation and development. Afterward, different models are compared, and it is found that the BiLSTM with multi-head self-attention model achieved the lowest mean squared error, which is because of its outstanding predicting ability in asymmetric separation cases. The work of this paper indicates that the quasi-3D loss prediction model proposed in this paper will be beneficial to the flow separation structure rapid prediction and cascade loss accurate evaluation in compressor design.
1 March 2024 in Physics of Fluids
Combining tandem cascades and curved vanes can mitigate the separation in highly loaded compressor cascades. Flow loss mechanisms in curved tandem cascades are crucial for fundamental design and optimization. This study investigates the flow losses and vortex structures in curved tandem cascades with different curved angles and an original straight tandem cascade. Numerical simulations are conducted at variable incidence angles. The results indicate no consistent effect of curved angles on the aerodynamic performance of curved tandem cascades. The tandem cascade with a curved angle of 5° effectively reduces losses at all incidence angles, while the tandem cascade with a curved angle of 15° extends the critical incidence angle to 3°. The comparative analyses reveal that curved vanes increase spanwise pressure gradients, causing low-energy fluid near endwalls to move toward the midspan. The weighting coefficient of losses quantitatively describes that curved vanes weaken the trailing edge shedding vortices of both vanes and passage vortex while enhancing the end wall spanwise vortex of the front vane, thus affecting the loss distribution. Finally, this study innovatively applies topological analysis methods to curved tandem cascades, establishing the relationship between topological structures and vortex structures in corner regions of tandem cascades, which provides a valid research approach to reveal the vortex dynamics mechanisms of the loss distribution in tandem cascades influenced by curved vanes.
10 January 2024 in Journal of Thermal Science
1 September 2023 in Physics of Fluids
An extensive numerical investigation is carried out to study the effects of single-slot bleed and porous bleed on the flow separation control in a transonic compressor stator. Two single slots in different locations and three staggered rows of circular holes are placed on the suction surface. Five bleed pressure ratios are examined for each bleed scheme at the design inlet Mach number of 1.0. The numerical results show that the porous bleed performs similar to the downstream slot bleed in terms of pressure loss control when the bleed pressure ratio is below 1.0. The maximum relative reduction in total pressure loss is 73%. The stable working range of downstream slot bleed is between 0.75 and 1.0 bleed pressure ratio, which is narrower than the range of porous bleed. The bleeding acceleration and favorable pressure gradients on the suction surface are key reasons for keeping the boundary layer from separating. The position of the aft edge of the bleed configuration is a critical parameter. It determines the ultimate range of adverse pressure gradients that the blade surface boundary layer needs to withstand. The similar performance of porous bleed and slot bleed is caused by their identical aft edge position. The high shock losses caused by a single shock wave result in a narrow stable working range for single-slot bleed. Multiple shocks and side bleeding in porous bleed mitigate the influences of shock wave losses and extend its working range.
20 March 2024 in Journal of Thermal Science