21 December 2021 in Eastern-European Journal of Enterprise Technologies
Most production technologies require a uniform flow path of liquid from pressure distribution pipelines. To achieve this goal, it is proposed to introduce polymer additives into the liquid flow or to use converging distribution pipelines with a continuous longitudinal slot in the wall. To reduce the uneven operation of the distribution pipeline during discrete liquid dispensing, it is proposed to use cylindrical output rotary nozzles with a lateral orthogonal entry of the jet into the nozzle. The problem is the lack of methods for accurate hydraulic calculation of the operation of distribution pipelines. Adequate calculation methods are based on differential equations. Finding the exact solution of the differential equation of fluid motion with variable path flow rate for perforated distribution pipelines is urgent, because it still does not exist. The available calculation methods take into account only the right angles of separation of the jets from the flow in the distribution pipeline. These methods are based on the assumption that the coefficient of hydraulic friction and the coefficient of resistance of the outlets are constant along the flow. A calculation method is proposed that takes into account the change in the values of these resistance coefficients along the distribution pipeline. The kinematic and physical characteristics of the flow outside the distribution pipeline are also taken into account. The accuracy of calculating the value of the flow rate of water distributed from the distribution pipeline has been experimentally verified. The error in calculating the water consumption by the method assuming that the values of the resistance coefficients are unchanged along the distribution pipeline reaches 18.75 %. According to the proposed calculation method, this error does not exceed 6.25 %. However, both methods are suitable for the design of pressure distribution pipelines, provided that the jet separation angles are straight. Taking into account the change from 90° to 360° of the angle of separation of the jets from the flow in the distribution pipeline will expand the scope and accuracy of calculation methods.
8 May 2019 in Eastern-European Journal of Enterprise Technologies
Studying the mutual interaction of hydraulic characteristics of waterdistributing pipelines and their spraying devices in the coolers at energy units
31 October 2022 in Eastern-European Journal of Enterprise Technologies
The results of an experimental study of the hydraulic friction factor of perforated pipelines that work with the collection of fluid along the path are reported. Clarification of this issue will make it possible to solve an important engineering task – to devise a reliable procedure for the hydraulic calculation of perforated pipes. The experiments were carried out on an assembled experimental bench. A steel pipeline with a perforated part of 1–3 m was investigated. Perforation holes were taken with a diameter of 3.6 and 9 mm. In the experiments, fluid flow, pressure loss, and average velocity were measured. Based on the data obtained, the values of the coefficient under study were calculated. It has been established that it is significantly larger than its values with uniform movement and is variable in length of the pipeline. Experimental dependences λcol on the value of the ratio of the velocities of the flowing jets of liquid to the average flow velocity in the corresponding section (Uh/V), as well as on the design characteristics of the channel, were obtained. It is shown that the lower value of the degree of pipe perforation corresponds to the higher values of λcol. This result can be explained by the influence of the attached flow rate on the main flow. The confirmation of this conclusion is the resulting shapes of diagrams of the average flow velocity obtained in the experiments, which differ significantly from standard diagrams with uniform motion. Obviously, additional energy is spent on the reformation of the velocities, and this causes additional head losses. Dependences were obtained for calculating the considered coefficient for prefabricated pipelines, including in the presence of transit flow rate. Their use in the calculation of the pipes under consideration will increase the reliability and efficiency of the sewage treatment plant, in which they are important structural elements
1 February 2023 in Journal of Ecological Engineering
Small river basins are complex self-regulatory systems, as well as indicators of the state of the environment due to the level of anthropogenic pressure. Since any changes in the regime of small rivers are reflected in the entire hydrographic chain, the problem of estimating the anthropogenic...
21 December 2023 in Eastern-European Journal of Enterprise Technologies
The object of the study in this paper is collecting perforated drainage pipelines, in particular, the determination of the hydraulic friction factor λdr, which significantly affects the parameters of the investigated pipes. Clarifying this issue will solve an important engineering problem – to develop a reliable method for hydraulic calculation of collecting perforated drainage pipes. As the main drawback of most of the available theoretical and experimental works on this topic is the insufficient consideration of the filtration characteristics of the surrounding soil and the material of the pipeline walls. Experimental studies of pressure drainage pipes with different design characteristics made it possible to find out the real picture of fluid flow in the pipe. Based on the research results, experimental dependences of λdr on the ratio of the fluid inflow velocity to the average flow velocity in the corresponding section (Uh/V), as well as on the design characteristics of the channel were obtained. The maximum possible flow that can be collected and passed by a collecting drainage pipeline with the specified design and filtration characteristics is determined. It is shown that a larger value of the specified ratio corresponds to larger values of λdr. This result can be explained by the effect of the attached flow on the main flow. Obviously, some energy is spent on the interaction of the attached and the main flow in the pipe, which leads to additional head losses. In the paper, dependencies were obtained for calculating the studied factor for collecting drainage pipelines. Using them in the calculation of drainage pipes will increase the reliability and efficiency of land reclamation systems, in which these pipelines are important structural elements