31 January 2019 in EUREKA: Physics and Engineering
The presented work is devoted to solving the actual problem of increasing the efficiency of rapid sand filters with granular filling, which operate at a constant filtration rate when cleaning suspensions with a relatively high concentration of contaminants. The proposed mathematical model for clarifying the suspension by filtration consists of three interconnected blocks: clarified, filtration, and hydraulic. Convenient dimensionless mathematical dependencies are obtained for calculating the concentrations of contaminants and sediment from the height of the filter and suspension in the filtrate; head loss in the filter loading; the effective time of the filter (the duration of the filter cycle). The design of the experimental setup and the methodology for conducting experimental studies and mathematical processing of the results are valid. The results of experimental studies of the suspension filtering process through the granular loading are presented, and the obtained data is analyzed. Measurement of pressure losses in the filter loading is performed when a suspension is passed with a relatively high concentration of contaminants at various filtration rates. The nature of the change in the filtration rate with time and height (length) loading at various filtration rates and initial contamination concentrations is determined. Measured variable concentration of suspended matter in filtered water and retained contamination over time. As a result of the experiments, it is confirmed that an increase in the concentration of retained contaminants S leads to an increase in the parameter Δn/n. Upon reaching a certain value of the concentration of the retained sediment S (in our case S=30 g/dm3), an increase in the relative specific volume of the sediment greater than Δn/n0=0.65 is not observed. It is established that an important characteristic of the retained sediment is the ratio of the volume concentration of the sediment to the volume concentration of solid particles in this sediment γ=Csd/Сs. The values of the adhesion and detachment of particles of contaminant in the particles of the material loading =4,9; =0,009. The results of experimental studies in general confirm the correctness and reliability of the obtained analytical dependencies.
21 December 2021 in Eastern-European Journal of Enterprise Technologies
Most production technologies require a uniform flow path of liquid from pressure distribution pipelines. To achieve this goal, it is proposed to introduce polymer additives into the liquid flow or to use converging distribution pipelines with a continuous longitudinal slot in the wall. To reduce the uneven operation of the distribution pipeline during discrete liquid dispensing, it is proposed to use cylindrical output rotary nozzles with a lateral orthogonal entry of the jet into the nozzle. The problem is the lack of methods for accurate hydraulic calculation of the operation of distribution pipelines. Adequate calculation methods are based on differential equations. Finding the exact solution of the differential equation of fluid motion with variable path flow rate for perforated distribution pipelines is urgent, because it still does not exist. The available calculation methods take into account only the right angles of separation of the jets from the flow in the distribution pipeline. These methods are based on the assumption that the coefficient of hydraulic friction and the coefficient of resistance of the outlets are constant along the flow. A calculation method is proposed that takes into account the change in the values of these resistance coefficients along the distribution pipeline. The kinematic and physical characteristics of the flow outside the distribution pipeline are also taken into account. The accuracy of calculating the value of the flow rate of water distributed from the distribution pipeline has been experimentally verified. The error in calculating the water consumption by the method assuming that the values of the resistance coefficients are unchanged along the distribution pipeline reaches 18.75 %. According to the proposed calculation method, this error does not exceed 6.25 %. However, both methods are suitable for the design of pressure distribution pipelines, provided that the jet separation angles are straight. Taking into account the change from 90° to 360° of the angle of separation of the jets from the flow in the distribution pipeline will expand the scope and accuracy of calculation methods.
31 October 2022 in Eastern-European Journal of Enterprise Technologies
The results of an experimental study of the hydraulic friction factor of perforated pipelines that work with the collection of fluid along the path are reported. Clarification of this issue will make it possible to solve an important engineering task – to devise a reliable procedure for the hydraulic calculation of perforated pipes. The experiments were carried out on an assembled experimental bench. A steel pipeline with a perforated part of 1–3 m was investigated. Perforation holes were taken with a diameter of 3.6 and 9 mm. In the experiments, fluid flow, pressure loss, and average velocity were measured. Based on the data obtained, the values of the coefficient under study were calculated. It has been established that it is significantly larger than its values with uniform movement and is variable in length of the pipeline. Experimental dependences λcol on the value of the ratio of the velocities of the flowing jets of liquid to the average flow velocity in the corresponding section (Uh/V), as well as on the design characteristics of the channel, were obtained. It is shown that the lower value of the degree of pipe perforation corresponds to the higher values of λcol. This result can be explained by the influence of the attached flow rate on the main flow. The confirmation of this conclusion is the resulting shapes of diagrams of the average flow velocity obtained in the experiments, which differ significantly from standard diagrams with uniform motion. Obviously, additional energy is spent on the reformation of the velocities, and this causes additional head losses. Dependences were obtained for calculating the considered coefficient for prefabricated pipelines, including in the presence of transit flow rate. Their use in the calculation of the pipes under consideration will increase the reliability and efficiency of the sewage treatment plant, in which they are important structural elements
29 June 2021 in Municipal economy of cities
A system of two differential equations which describes the movement of fluid in a pipe with a variable flow rate and the conditions for the fluid outflow through the walls of drainage pipelines into the surrounding soil is considered. It is reasoned that the second term in the original equation, which takes into account energy losses associated with a flow rate variation along the length, can be neglected without a substantial error. The considered system is reduced to dimensionless form by introducing original variables. The coefficient of collecting drainage pipeline resistance «ζl» and the generalized parameter «A», which take into account the structural and hydraulic characteristics of the considered flow, are two main parameters used in the analysis. The concept of an infinitely long drainage pipeline (a pipeline with an infinite walls filtration capacity) is introduced in the article. Also it is noted that such pipeline will have a maximum throughput comparing to pipes of the same diameter but limited length. Quite simple and practical calculated dependencies for the determination of the nature of flow rate variation and pressure drop along the length of the pipeline were received on the basis of the conducted analysis. Important characteristics of pressure distribution pipelines were calculated on the basis of offered formulas. Corresponding graphical dependencies were built for visibility. In particular, graphs of the flow rate variation at the end of the distributor, depending on the design and filtration characteristics of the «soil-drain» system, are presented. Graph that shows the dependence of the variation in the flow rate distribution unevenness along the length of the drainage pipe at various hydraulic conductivity values of the surrounding soil is important for understanding the drainage pipelines particularity. The necessity to take into account the nature of the flow rate connection unevenness along the length for obtaining reliable results for real drainage pipelines calculation is demonstrated.
21 December 2023 in Eastern-European Journal of Enterprise Technologies
The object of the study in this paper is collecting perforated drainage pipelines, in particular, the determination of the hydraulic friction factor λdr, which significantly affects the parameters of the investigated pipes. Clarifying this issue will solve an important engineering problem – to develop a reliable method for hydraulic calculation of collecting perforated drainage pipes. As the main drawback of most of the available theoretical and experimental works on this topic is the insufficient consideration of the filtration characteristics of the surrounding soil and the material of the pipeline walls. Experimental studies of pressure drainage pipes with different design characteristics made it possible to find out the real picture of fluid flow in the pipe. Based on the research results, experimental dependences of λdr on the ratio of the fluid inflow velocity to the average flow velocity in the corresponding section (Uh/V), as well as on the design characteristics of the channel were obtained. The maximum possible flow that can be collected and passed by a collecting drainage pipeline with the specified design and filtration characteristics is determined. It is shown that a larger value of the specified ratio corresponds to larger values of λdr. This result can be explained by the effect of the attached flow on the main flow. Obviously, some energy is spent on the interaction of the attached and the main flow in the pipe, which leads to additional head losses. In the paper, dependencies were obtained for calculating the studied factor for collecting drainage pipelines. Using them in the calculation of drainage pipes will increase the reliability and efficiency of land reclamation systems, in which these pipelines are important structural elements
22 April 2023 in Problems of Water supply, Sewerage and Hydraulic
В даній роботі представлені досить прості і зручні для застосування аналітичні залежності для розрахунку основних гідравлічних і конструктивних характеристик розподільчих дренажних трубопроводів, що прокладені з певним похилом. Вони запропоновані на основі аналізу системи диференційних рівнянь, яка складається з рівняння гідравліки змінної маси і модифікованого рівняння фільтрації, і описує рух рідини у таких трубопроводах. Розв’язки вихідної системи рівнянь отримані за припущення нехтування членом, який враховує ефект зміни витрати вздовж шляху. При аналізі використано поняття нескінченно довгого розподільчого дренажного трубопроводу, який прокладений з похилом, або, що те ж саме, похильного трубопроводу з нескінченною фільтраційною спроможністю стінок бічної поверхні. За запропонованими формулами проведена серія розрахунків основних характеристик даних труб при різних значеннях похилу, для наочності побудовані відповідні графічні залежності. Показано, що величина геометричного похилу прокладання напірного розподільчого дренажного трубопроводу, разом з коефіцієнтом опору і узагальненим параметром A, суттєво впливає на розрахункові параметри таких труб.