Alfredo Petrauski

Alfredo Petrauski

Auto-generated profile, based on publicly available information

Alfredo Petrauski

Universidade Estadual do Oeste do Paraná, Brasil

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2016 in Revista Árvore
Verified
Journal Article
Open access
PDF file
SPSandra Maria Ferreira Couri Petrauski
Sandra Maria Ferreira Couri Petrauski
JSJosé de Castro Silva
José de Castro Silva
APAlfredo Petrauski
Alfredo Petrauski
RLRicardo Marius Della Lucia
Ricardo Marius Della Lucia
This study evaluated the structural behavior of porticos made from eucalyptus glued boards, using wood of Eucalyptus sp and resorcinol formaldehyde adhesive. Three units, in real scale, of tri-articulated straight porticos, with a 5 meter porthole and a 26º inclination, capable to support tiles covering placement were designed, constructed and subjected to load testing, until rupture. The amount of adhesive used in the construction of the porticos was 250 g/m2 and the bonding pressure of 1.3 MPa. The Hankinson model was employed as an estimator of the glued joints strength, under different angles between the fibers. The average value for the last resistance of the structures was 4.63 times the design load, according to the criteria established by the ABNT, 1997. The structures showed satisfactory mechanical performance and deformations lower than the ones allowed by the standard. It was concluded there is technical feasibility to manufacture porticos fully bonded with small thickness veneers.

17 October 2022 in Research, Society and Development
Verified
Journal Article
Open access
PDF file
SPSandra Maria Ferreira Couri Petrauski
Sandra Maria Ferreira Couri Petrauski
MPMateus Couri Petrauski
Mateus Couri Petrauski
APAlfredo Petrauski
Alfredo Petrauski
DPDesirè Coraça Possa
Desirè Coraça Possa
RARicardo Lessa Azevedo
Ricardo Lessa Azevedo
GDGustavo Lacerda Dias
Gustavo Lacerda Dias
A fórmula de Hankinson estima propriedades de resistência da madeira quando o material está recebendo forças inclinadas em relação à direção das fibras. No Brasil, por força de orientação normativa, costuma-se usar o valor fixo igual a 2 para o expoente β dos seno e cosseno da fórmula, mas pode ocorrer melhores ajustes para expoentes β diferentes deste valor. O objetivo deste trabalho foi evidenciar, a partir de cinco experimentos independentes, a adequação da fórmula de Hankinson para estimar a resistência de juntas coladas à diferentes ângulos, quando rompidas sob compressão. Adicionalmente, procurou-se analisar a diferença de desempenho mecânico de juntas coladas quando o ensaio se dá por compressão ou por torção. Neste trabalho, os valores dos parâmetros β variaram entre 1,82 e 2,18, com média de 2,02, valor próximo ao adotado em norma. As juntas coladas rompidas por compressão apresentaram perda de resistência com o aumento do ângulo de colagem. Já no ensaio sob torção, a resistência sofreu pouca influência do ângulo de colagem. Verificou-se que a fórmula de Hankinson é adequada para estimar a resistência de juntas coladas à diferentes ângulos entre as fibras da madeira, quando a ruptura ocorre por compressão, mas não parece adequada para a obtenção da estimativa de resistência sob torção. As juntas coladas rompidas à compressão apresentaram resistência diferente de juntas coladas rompidas sob momento de torção. No conjunto, tanto a fórmula de Hankinson quanto os ensaios conduzidos à torção podem permitir a verificação de ligações coladas sujeitas simultaneamente a forças e momentos.

1 January 2023 in Revista Árvore
Verified
Journal Article
Open access
PDF file
VPVictor Hugo Lazzaretti Padilha
Victor Hugo Lazzaretti Padilha
APAlfredo Petrauski
Alfredo Petrauski
ASAlessandra dos Santos
Alessandra dos Santos
DPDesirè Coraça Possa
Desirè Coraça Possa
SPSandra Maria Ferreira Couri Petrauski
Sandra Maria Ferreira Couri Petrauski
GSGustavo Savaris
Gustavo Savaris
Glued Laminated Timber technology allows the construction of wooden structural components bonded with adhesive. This technology enables the creation of large-scale structures, with technological control over the material, and in a competitive industrial system. Focusing on the structural application of wood, the present study assessed the strength of bonded joints with different angles between the fibers of Pinus sp. wood, joined with a two-component polyurethane adhesive based on vegetable oils. The bonded joints were fabricated with angles of 0°, 10°, 20°, 30°, 45°, 60°, 70°, 80°, and 90°, and were evaluated for shear strength under compression and torsion. When regression analysis was performed, shear compression values showed compliance with Hankinson’s equation, with an R2 value close to 0.76. However, shear torsion results yielded R2 values near 0.17. Thus, Hankinson’s equation was unsuitable as an estimator for torsional shear strength values. The specimens showed a different mechanical response to shear when tested in compression compared to those tested in torsion.

1 January 2023 in Revista Árvore
Verified
Journal Article
Open access
PDF file
KTKarina Taiza Tomé
Karina Taiza Tomé
APAlfredo Petrauski
Alfredo Petrauski
DPDesirè Coraça Possa
Desirè Coraça Possa
VPVictor Hugo Lazzaretti Padilha
Victor Hugo Lazzaretti Padilha
SPSandra Maria Couri Petrauski
Sandra Maria Couri Petrauski
MPMateus Couri Petrauski
Mateus Couri Petrauski
The main function of the adhesive is to promote adhesion between materials, as well as provide fluidity and fill in the gaps between joints. Information such as grammage and bonding pressure is fundamental when it comes to the execution of structures in glued laminated wood. In this sense, the objective of this study was to evaluate the shear strength in compression of bonded joints using a one-component polyurethane adhesive with cold curing at three different gram levels, being 150 g.m-2, 200 g.m-2 and 250 g.m-2, with spreading on a single face, applied at two pressure levels, 0.7 MPa, and 1.0 MPa. The apparent density was determined, and with that, four blocks/density groups were obtained, which comprised four repetitions. In addition, the percentage of failure in the specimens after performing the shear test was analyzed. Statistical data analysis was carried out adopting a randomized design in a 2x3 factorial block to analyze the effects of grammage and bonding pressure on wood strength and failure The homogeneity and normality of the data were tested, and later the analysis of variance (ANOVA). The results showed that the joints’ strength was not affected, both for weight and pressure levels. As for the wood failure percentage, the values obtained were low, with averages below 35%.

16 January 2022 in Research, Society and Development
Verified
Journal Article
Open access
DPDesirè Coraça Possa
Desirè Coraça Possa
APAlfredo Petrauski
Alfredo Petrauski
SPSandra Maria Ferreira Couri Petrauski
Sandra Maria Ferreira Couri Petrauski
GSGustavo Savaris
Gustavo Savaris
RJRodrigo Aparecido Jordan
Rodrigo Aparecido Jordan
ATAdolfo Lll Echeandia La Torre
Adolfo Lll Echeandia La Torre
A indústria da construção civil é uma grande consumidora de recursos naturais, gerando muitos resíduos e sendo responsável por grande parte dos impactos ambientais mundiais. O emprego da madeira em estruturas ressurge como um material ambientalmente correto no setor da construção civil e agrícola por ser um material construtivo/estrutural renovável e seu uso de forma permanente contribui com a redução das emissões de carbono na atmosfera. Com isso, o presente estudo objetivou executar e ensaiar pórticos com tirantes, feitos em madeira laminada colada, de modo a avaliar sua aplicação estrutural em aviários. Foram confeccionados quatro pórticos em escala reduzida com tirantes de barras rosqueadas de 3/8”, com vão livre de 1,9 metros e altura de pilar de 1,83 metros. Os materiais utilizados para a confecção dos pórticos foram a madeira de Pinus sp. e adesivo bicomponente à base de óleos vegetais. As estruturas romperam para uma carga média de 1,37 vezes a carga de verificação estabelecida e exibiram deslocamentos próximos a linearidade mesmo para cargas elevadas. Ainda, obteve-se um coeficiente de correlação de 0,95 entre a densidade aparente da madeira dos pórticos com sua resistência. Desta forma, as evidências obtidas indicam que o emprego do tirante nas estruturas promoveu a melhoria do desempenho mecânico quanto à resistência e rigidez.

1 October 2024 in Revista Árvore
Verified
Journal Article
Open access
PDF file
APAlfredo Petrauski
Alfredo Petrauski
MPMateus Couri Petrauski
Mateus Couri Petrauski
ASAlessandra dos Santos
Alessandra dos Santos
SPSandra Maria Ferreira Couri Petrauski
Sandra Maria Ferreira Couri Petrauski
DPDébora Coraça Possa
Débora Coraça Possa
Reforestation trees are an alternative to meet industrial needs, and one potential application is their use in prefabricated structures, such as glued laminated timber (glulam). This study aimed to evaluate the shear strength of Pinus sp. bonded joints made using a single-component polyurethane adhesive (1C-PUR). The joints were produced varying the angles between the wood fibers ranging from 0º to 90º and were tested subjected to shear under compression load and to shear under torsional load. The use of the Hankinson’s equation as an estimator of shear strength of glued joints and the percentage of wood failure were also evaluated. A total of 144 specimens were tested. Half of the total was subjected to shear test under compression load while the other half was subjected to shear test under torsional load. The wood laminates used to make the joints were previously divided into eight groups according to their apparent density. The results showed that the shear strength was affected by the bonding angle, especially for those tested under compression loads. The mechanical behavior of the shear test under compression was considered different from that of the test under torsion for six of the nine angles used in the study. It was also found that Hankinson’s equation can be used as an estimate of the shear strength of joints bonded on different angles when the tests are performed under compression loads. However, the equation was not appropriate for estimating the test results when shear was caused by torsional loads. Overall, the bonded joints presented satisfactory shear strength and low percentage of wood failure. Furthermore, the results of this research were in accordance to those found on similar research where other adhesives were used.