1 January 2018 in Journal of Nuclear Materials
1 August 2018 in Nuclear Materials and Energy
24 March 2016 in Philosophical Magazine
Indentation size effects (ISEs) are well known in static indentation of materials that deform by dislocation-based mechanisms. However, whilst instrumented indentation techniques have become rapidly established as a means of determining the near-surface mechanical properties of materials, scratch testing has been much less widely used. Hardness is used in wear models as a proxy for the yield stress, and the design of materials and hard coatings has often sought to exploit size-derived performance enhancements through length-scale engineering. Yet, it is not known directly whether (or not) length-scale effects also apply to scratch (and thus wear) performance at small scales, or what the functional form of this effect is. This work directly demonstrates that there is a lateral size effect (LSE) and shows that there are questions to be answered if the use of hardness as an indicator of wear performance is to remain valid. We report on constant load scratch experiments using a Berkovich indenter on single-crystal, annealed copper, using a range of applied normal forces and compare results from three scratch hardness calculation methods to indentation hardness (ISO 14577:2002) measured on the same sample at the same loads. Scratch tests were performed with the Berkovich indenter aligned either edge forward or face forward to the scratch direction. In all cases, we demonstrate that there is a very significant (approximate factor of two) effect of scratch size (an LSE) on scratch hardness. The results also show that the deformation mechanisms occurring in scratch tests are different to those occurring beneath a static indentation and that different mechanisms dominated for different stylus orientations (face-forward vs. edge-forward orientation). This is, to our knowledge, the first direct demonstration of an LSE akin to the ISE in metallic materials. The results have significant implications for using static indentation as a predictor of deformation during wear processes.
27 December 2022 in Acta Materialia
2 May 2023 in Materials Science and Engineering: A
29 September 2016 in Philosophical Magazine
It has been reported previously that, for single and polycrystalline copper (fcc), the indentation size effect and the grain size effect (GSE) can be combined in a single length-scale-dependent deformation mechanism linked to a characteristic length-scale calculable by a dislocation-slip-distance approach (X. D. Hou and N. M. Jennett, ‘Application of a modified slip-distance theory to the indentation of single-crystal and polycrystalline copper to model the interactions between indentation size and structure size effects,’ Acta Mater., Vol. 60, pp. 4128–4135, 2012). Recently, we identified a ‘lateral size effect (LSE)’ in scratch hardness measurements in single crystal copper, where the scratch hardness increases when the scratch size is reduced (A. Kareer, X. D. Hou, N. M. Jennett and S. V. Hainsworth ‘The existence of a lateral size effect and the relationship between indentation and scratch hardness’ Philos. Mag. published online 24 March 2016). This paper investigates the effect of grain size on the scratch hardness of polycrystalline copper with average grain sizes between 1.2 and 44.4 μm, when using a Berkovich indenter. Exactly the same samples are used as in the indentation investigation by Hou et al. (‘Application of a modified slip-distance theory to the indentation of single-crystal and polycrystalline copper to model the interactions between indentation size and structure size effects,’ Acta Mater., Vol. 60, pp. 4128–4135, 2012). It is shown that, not only does the scratch hardness increase with decreasing grain size, but that the GSE and LSE combine in reciprocal length (as found previously for indentation) rather than as a superposition of individual stresses. Applying the same (as indentation) dislocation-slip-distance-based size effect model to scratch hardness yielded a good fit to the experimental data, strongly indicating that it is the slip-distance-like combined length-scale that determines scratch hardness. A comparison of the fit parameters obtained by indentation and scratch on the same samples is made and some distinct differences are identified. The most striking difference is that scratch hardness is over four times more sensitive to grain size than is indentation hardness.