Dylan Agius

Dr. Dylan Agius


Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2020 in Computational Materials Science
Verified
Journal Article
Closed access
DADylan Agius
Dylan Agius
AMAbdullah Al Mamun
Abdullah Al Mamun
CSChris A. Simpson
Chris A. Simpson
CTChristopher Truman
Christopher Truman
YWYiqiang Wang
Yiqiang Wang
DKDavid Knowles
David Knowles

2 May 2023 in Materials Science and Engineering: A
Verified
Journal Article
Open access
EHEdward William Horton
Edward William Horton
EDEralp Demir
Eralp Demir
DADylan Agius
Dylan Agius
AKAnna Kareer
Anna Kareer
DCDavid M. Collins
David M. Collins
DKDavid Knowles
David Knowles

12 February 2020 in Applied Sciences
Verified
Journal Article
Open access
PDF file
BMBarry Mooney
Barry Mooney
DADylan Agius
Dylan Agius
KKKyriakos I. Kourousis
Kyriakos I. Kourousis
This short communication offers a preliminary view on ongoing research conducted on the as-built EOS maraging steel 300. The material’s cyclic elastoplastic characteristics under strain-controlled loading have been investigated experimentally. Specimens fabricated under two primary orientations, horizontally and vertically to the build plate, have been tested. The obtained stress–strain hysteresis loops exhibited symmetry, with the vertical specimen showing a higher plastic strain energy dissipation capability than the horizontal specimen. Modelling of the material’s elastoplastic behaviour was performed with a commonly used kinematic hardening rule, combined with both isotropic and anisotropic yield functions and elasticity moduli. The obtained simulations of the hysteresis loops, from the implementation of these two plasticity models, indicate the advantage of the anisotropic modelling approach over the isotropic approach. The anisotropic plasticity model describes in a more representative way the inherent elastic and plastic anisotropy of the as-built material. Further research is underway to explore the low cycle fatigue performance of this additively manufactured metal.

7 September 2021 in Journal of Physics: Materials
Verified
Journal Article
Open access
DADylan Agius
Dylan Agius
POPatrick O’tOole
Patrick O’tOole
CWChris Wallbrink
Chris Wallbrink
ZSZoran Sterjovski
Zoran Sterjovski
CWChun Hui Wang
Chun Hui Wang
GSG B Schaffer
G B Schaffer
The ability to simultaneously predict the microstructure and bulk material properties of 3D printed (additively manufactured or AM) metals is critical to the development of process intelligence that can be used by a digital-twin for forecasting and optimising alloy composition and fabrication parameters. This study proposes a simulation framework for predicting the microstructure and corresponding meso- and macro-scale properties of AM materials. This is achieved by integrating phase-field and crystal plasticity modelling techniques, whereby the phase field model predicts the microstructure and the crystal plasticity constitutive model computes the stress–strain evolution using the microstructure as the input. The simulation of multiple microstructures demonstrates that this integrated approach can be used to test the influence of different microstructures on the mechanical properties of titanium alloy Ti-5553. This includes the influence of grain size and grain orientation on both the meso- and macro-scale behaviour.


20 June 2022 in MethodsX
Verified
Journal Article
Open access
DADylan Agius
Dylan Agius
AMAbdullah Al Mamun
Abdullah Al Mamun
CTChristopher Truman
Christopher Truman
MMMahmoud Mostafavi
Mahmoud Mostafavi
DKDavid Knowles
David Knowles
A tool to implement a length scale dependency to classical crystal plasticity simulations is presented. Classical crystal plasticity models do not include a size effect; therefore, the size of the grain does not influence the simulated deformation. Classical crystal plasticity advancements have been through the inclusion of stress or strain gradient based constitutive models to improve the simulation of length scale dependent deformation. However, this tool presents an alternative to implementing a length scale, where the influence of slip pile-up in the form of dislocations at grain boundaries as a potential to explaining the Hall-Petch effect in materials. This is achieved by calculating the slip distance in adjacent grains for each slip system, by assuming the total slip length spans the grain in the slip direction. These calculations can occur in two ways. The first is the analysis occurs at the start of the simulation, therefore, only occurs once. If this approach is used, the computational cost of this tool is minute. However, if the simulations consider large deformations, during which it is expected that the grains are going to undergo large rotations, then it would be advantageous to the have the tool recalculate the information during the analysis. Consequently, the computational cost would depend on the resolution of the modelled geometry, the number of grains, and the number of slip systems. The tool also provides a capability to develop constitutive models based on complex grain boundary features which can be implemented in classical crystal plasticity models and gradient based crystal plasticity models. The described calculation process is implemented through a Fortran subroutine, which has been designed to be easily used in crystal plasticity simulations. The presented tool also includes Python code designed to link with microstructures built using DREAM.3D to extract the required input data to the Fortran subroutine.