20 January 2021 in IEEE Microwave and Wireless Components Letters
This letter presents single-ended and differential D-band power amplifiers (PAs) in 55nm SiGe BiCMOS technology. The proposed PAs exploit the remarkable features of common-base stages for rising the power efficiency, i.e., 1) higher breakdown voltage; 2) sharp compression profile due to the enhanced linearity; and 3) supply current adapted to the signal amplitude by means of current clamping. A four-stage single-ended PA proves P 1dB = 16.8 dBm with P SAT = 17.6 dBm at 135 GHz. The PAEs at P 1dB and P 1dB-6 dB are 17.1% and 8.5%, respectively. With a differential PA, the linear output power is increased to P 1dB = 18.5 dBm with P SAT = 19.3 dBm at 135 GHz. The PAEs at P 1dB and P 1dB-6 dB are 12.6% and 6.7%, respectively. The PAs demonstrate 3× PAE improvement in the linear region against the state of the art.
21 July 2021 in IEEE Transactions on Microwave Theory and Techniques
Emerging applications in D-band (110–170GHz) demand amplifiers with high gain-bandwidth (GBW) products. In this frequency range, the cascode stage offers superior available gain, thanks to the high output impedance, but the design of the output matching network entails a GBW tradeoff. The issue is deeply investigated in this work. Simple, closed-form equations for gain and bandwidth as a function of the load reflection coefficient are derived, leading to the following design insights: 1) for maximum gain and bandwidth, the output matching network should be implemented with positive (magnetic) reactances; 2) with lossy reactances, an optimal load reflection coefficient exists to maximize the power gain, ${\Gamma '_{L-{\mathrm{ opt}}}}$ ; and 3) by selecting ${\Gamma '_{L} < \Gamma '_{L-{\mathrm{ opt}}}}$ , the bandwidth increases quickly with a marginal gain penalty, finally enhancing the GBW product. Leveraging the results of the analysis, single-stage and multistage stagger-tuned amplifiers are implemented in SiGe BiCMOS technology. Two- and three-stage amplifiers demonstrate more than 60GHz bandwidth with 20 and 28dB gain, respectively, corresponding to 700GHz and 1.7 THz GBW. Normalizing gain and bandwidth to the number of stages and technology $f_{\max }$ , the resulting figure of merit is remarkably higher than previously reported silicon amplifiers in the same band.
27 July 2020 in IEEE Transactions on Circuits and Systems II: Express Briefs
The implementation of an unclocked DFE (UC-DFE) architecture for high-speed PAM-4 signals is investigated in this work. Instead of clocked slicers and flip-flops, data-decision and feedback delay control are performed by saturated analog delay chains. As a result, the UC-DFE, previously exploited for NRZ signals, saves power consumption and silicon area while the simple implementation allows operation at high data-rate. A receiver front-end comprising a linear equalizer and the proposed 2-tap UC-DFE scheme is designed in 7 nm FinFET technology. From post-layout simulations, the receiver recovers a PAM-4 signal at 112 Gb/s after an 18 dB loss channel with a power efficiency of 0.47 pJ/bit. The receiver also works with NRZ signals at half the bit-rate equalizing 24dB channel loss with a power efficiency of 0.70 pJ/bit.
31 July 2020 in IEEE Solid-State Circuits Letters
This paper presents 1-stage and 2-stage compact Dband amplifiers with lumped-element matching networks implemented in 55 nm SiGe BiCMOS. To correctly account for the effects of a non-ideal ground plane, i.e. reactances in current return paths, and coupling of inductors with nearby layout structures, a shielded 2-port, 4-terminal simulation strategy for inductors is proposed. Validated by measurements, the approach allows very accurate design of compact amplifiers in D-band. The 1-stage design proves 11.8 dB gain at 152 GHz and 17.9 GHz bandwidth in 0.031 mm2. With the 2-stage amplifier, featuring 20.1 dB gain at 150 GHz with 24.5 GHz bandwidth in 0.058 mm2, from 2x to 5.7x area reduction is demonstrated against similar SiGe amplifiers in the same frequency band.