A four-level pulse-amplitude modulation (PAM-4) transceiver operating up to 64 Gb/s in 28-nm CMOS fully depleted silicon-on-insulator (FDSOI) for short-reach electrical links is presented. The receiver equalization relies on a flexible continuous-time linear equalizer (CTLE), providing a very accurate channel inversion through a transfer function that can be optimally adapted at low frequency, mid-frequency, and high frequency independently. The CTLE meets the performance requirements of CEI-56G-VSR without requiring the decision feedback equalizer (DFE) implementation. As a result, timing constraints for comparators in data and edge sampling paths may be relaxed by using track-and-hold (T&H) stages, saving power consumption. At the maximum speed, the receiver draws 180 mA from 1-V supply, corresponding to 2.8 mW/Gb/s only. The transmitter embeds a flexible feed-forward equalizer (FFE) which can be reconfigured to comply with legacy standards. A comparison between current-mode (CM) and voltage-mode (VM) TX drivers is proposed, proving through experiments that the latter yields larger PAM-4 eye openings, thanks to the intrinsically higher speed. The full transceiver (TX, RX, and clock generation) operates from 16 to 64 Gb/s in PAM-4 and 8 to 32 Gb/s in non-return-to-zero (NRZ), and supports 2x and 4x oversampling to reduce data rate down to 2 Gb/s. A TX-to-RX link at 64 Gb/s, across a 16.8-dB-loss channel, reaches 10⁻¹² minimum bit-error rate (BER) and 0.19-UI horizontal eye opening at BER = 10⁻⁶, with 5.02 mW/Gb/s power dissipation.
16 September 2022 in IEEE Transactions on Microwave Theory and Techniques
A 16-element 140–160-GHz phased array transceiver is reported. The chipset is fabricated using STMicroelectronics’ 55-nm SiGe BiCMOS process. Five different chips are implemented: a 4-channel transmitter with a maximum gain per channel of 15 dB and 0-dBm saturated output power; a 4-channel receiver with a maximum gain of 8 dB, a $-$ 10.4-dBm input 1-dB compression point (IP ${_\mathrm{1\,dB}}$ ), and a minimum noise figure (NF) of 15.6 dB per channel; a 0–1-GHz to 140–160-GHz I/Q up-converter with integrated frequency doubler, exhibiting a $-$ 13.5-dB conversion gain (CG) and $-$ 6-dBm output 1-dB compression point using a 70–80-GHz local oscillator (LO); a 140–160-GHz to 0–1-GHz I/Q down-converter with integrated frequency doubler, exhibiting a CG of 0 dB and IP ${_\mathrm{1\,dB}}$ of 0 dBm using a 70–80-GHz LO and an 11.67–13.33-GHz to 70–80-GHz x6 frequency multiplier for the LO, delivering 5.6-dBm maximum output power. The chips are assembled together with 16 cavity-backed aperture-coupled patch antennas using a high-performance and low-cost commercial PCB, supported over a heat sink. The main challenges encountered during the integration of the proposed system are also discussed. The complete system is used to build a wireless radio link in the laboratory, demonstrating 2-D beam steering in a range of $\pm$ 30 $^\circ$ .
20 January 2021 in IEEE Microwave and Wireless Components Letters
This letter presents single-ended and differential D-band power amplifiers (PAs) in 55nm SiGe BiCMOS technology. The proposed PAs exploit the remarkable features of common-base stages for rising the power efficiency, i.e., 1) higher breakdown voltage; 2) sharp compression profile due to the enhanced linearity; and 3) supply current adapted to the signal amplitude by means of current clamping. A four-stage single-ended PA proves P 1dB = 16.8 dBm with P SAT = 17.6 dBm at 135 GHz. The PAEs at P 1dB and P 1dB-6dB are 17.1% and 8.5%, respectively. With a differential PA, the linear output power is increased to P 1dB = 18.5 dBm with P SAT = 19.3 dBm at 135 GHz. The PAEs at P 1dB and P 1dB-6dB are 12.6% and 6.7%, respectively. The PAs demonstrate 3× PAE improvement in the linear region against the state of the art.
1 April 2022 in IEEE Journal of Solid-State Circuits
This article presents a Ka-band bidirectional transceiver front end and its integration in an image-reject up/down converter module in 28-nm bulk CMOS. In the radio frequency (RF) front end, a transformer-based transmit/receive (T/R) switch is exploited for minimum area occupation without affecting the linearity and the isolation between the transmitter (TX) and receiver (RX) paths. The TX front end shows 19-dB power gain with an output-referred ${{ OP}_{ 1,dB}}$ of 14 dBm and 18.7% power-added efficiency (PAE). Tested with a 100-MHz 64-QAM orthogonal frequency-division multiplexing (OFDM) modulated input signal, the error vector magnitude (EVM) is below 5% up to an average output power of 6.6 dBm, with a corresponding 7% PAE. The RX in the front end features a minimum noise figure (NF) of 4.9 dB, with 17-dB power gain. The measured input IP3 is -9.2 dBm, while the power consumption is only 35 mW. The RF bandwidth is 22-31 GHz, wide enough to cover the fifth-generation (5G) new radio (NR) bands n257, n258, and n261. The RF front end is also monolithically integrated along with a broadband bidirectional frequency up/down converter, capable of translating the 5G modulated signal from/to a 3-GHz intermediate frequency (IF). The up/down converter is realized with a single bidirectional quadrature mixer shared between the TX and RX paths. At the IF, a single hybrid coupler is used for quadrature phase shifting in upconversion and recombination in downconversion while concurrently keeping the TX and RX IF paths isolated from each other. In the upconversion mode, the module features a 22-dB programmable conversion gain, with a 40-dB minimum in-band image rejection ratio (IRR). The downconversion path shows a 29-dB programmable conversion gain and a minimum measured NF and IRR of 8.5 and 30 dB, respectively, while consuming 110 mW.
26 November 2018 in IEEE Journal of Solid-State Circuits
Precise generation of quadrature signals over a wide frequency range is a key function for the next-generation 5G communication systems. In this paper, we present a wideband quadrature generator based on a single-stage polyphase filter (PPF). A phase detector senses the phase error from quadrature signals generated by a single-stage PPF, and a feedback circuit continuously tunes the filter center frequency to the input signal frequency by varying the polyphase resistance of an nMOS device in triode. Transformer-based resonant circuits at the input and output of the PPF ensure wide bandwidth and low loss. Prototypes have been realized in a 55-nm CMOS technology. Tailored to the next-generation 5G systems for cross-network interoperability requirements, the measured quadrature generator shows an image rejection ratio IRR > 40 dB over a bandwidth from 28 to 44 GHz. The power consumption is 36 mW for the PPF and buffers, and 3 mW only for the calibration loop. One key aspect of the proposed solution is its robustness over process, voltage and temperature (PVT), one of the weak aspects of alternatives proposed in the literature. This solution compares favorably with the state of the art and shows the largest fractional bandwidth (44%) among the quadrature generators at frequencies greater than 20 GHz, to authors' knowledge.