25 January 2018 in IEEE Transactions on Applied Superconductivity
Previous studies indicated that the use of high-temperature superconductors (HTS) in the highest field allows achieving the required magnetic flux in the central solenoid (CS) of the European DEMO at a reduced outer diameter, which would enable a reduced overall size and cost of DEMO. The proposed winding pack (WP) design of the CS1 module is based on 10 layer-wound sub-coils using HTS, react & wind Nb$_{3}$Sn and NbTi conductors in the high, medium and low field sections, respectively. The design utilizes a stainless steel and a superconductor grading leading to different overall current densities in each of the 10 sub-coils. Both, the hoop stress and the vertical loads are taken into consideration for determination of the required stainless steel cross-section in the winding pack. The stainless steel grading has been found to have an even more pronounced effect on the overall sub-coil current densities than the superconductor grading. A preliminary estimation of the space required for the pre-compression structure is also reported.
9 January 2020 in IEEE Transactions on Applied Superconductivity
State-of-the-art high field solenoids make use of hybrid designs exploiting the superior high field performance of High Temperature Superconductors (HTS) in the innermost region. The benefits of a hybrid Central Solenoid in a pulsed tokamak like the EU DEMO can be two-fold: either to reduce its outer radius (which would result in a reduced overall size and cost of the tokamak), or to increase the generated magnetic flux (which could extend the plasma burn time and possibly increase the power plant efficiency). In the framework of the pre-conceptual design studies for DEMO coordinated by EUROfusion, a hybrid Central Solenoid is proposed based on ten layer-wound sub-coils using HTS, Nb3Sn, and Nb-Ti conductors respectively for the high, medium, and low field sections. The design exploits the flexibility of layer winding by grading both the superconductor and the stainless steel cross sections in each sub-coil, which has the potential for space and cost savings. Mechanical analyses have identified fatigue as the main design driver for the EU DEMO Central Solenoid. Possible alternatives to reduce the sensitivity of the proposed design to fatigue are currently under investigation.
2 July 2019 in IEEE Transactions on Applied Superconductivity
Quench protection is a critical issue for magnet using high temperature superconducting (HTS) materials like REBCO. For cable-in-conduit conductor (CICC) with twisted REBCO tapes, which is considered for high current HTS conductor for fusion magnet, the anisotropic critical current density (Jc) of tape and complex conductor layout will further complicate the quench behavior. The CryoSoft code THEA is used to simulate the quench behavior of various sub-scale CICCs in view of a quench experiment in SULTAN facility. The CICCs are composed of the twisted tape stack assembled into copper shell (strand). It has been found that neglecting the anisotropy of Jc in quench simulation will significantly underestimate the hot spot temperature by about 40 K. Therefore, it could leave potential risk to damage the magnet. It is also shown that the thermal contact resistance between strand and the steel jacket (the conduit) plays a very important role on quench behavior. The hot spot temperature can be reduced by more than 100 K if the thermal resistance is reduced by two order of magnitude. On the other hand, variations of inter-strand electrical and/or thermal resistance have only very little influence (few Kelvin).
29 March 2010 in IEEE Transactions on Applied Superconductivity
One year of operation and test activity of the SULTAN test facility at CRPP-Villigen, from October 2008 to October 2009 is reviewed. The main improvements of the facility include a new control system for the cryo-plant and a new electric motor for the helium compressor. The range of operation for the SULTAN samples has been improved in terms of cyclic loading rate. The test campaigns from October 2008 to October 2009 include eight ITER TF conductor samples, two JT60SA samples and a number of other developmental samples. The highlights of the test campaign and the statistical data about cool-downs, warm-ups and test duration are reported. For the eight ITER TF samples, more detail is given about the joint development, the standard test program and the data reduction for the assessment of the results. Eventually, an outlook in the next operation period is also discussed.
1 September 2019 in Fusion Engineering and Design