9 September 2015 in Journal of Manufacturing Science and Engineering
This work develops a needle insertion force model based on fracture mechanics, which incorporates the fracture toughness, shear modulus, and friction force of the needle and tissue. Ex vivo tissue experiments were performed to determine these mechanical tissue properties. A double insertion of the needle into the tissue was utilized to determine the fracture toughness. The shear modulus was found by applying an Ogden fit to the stress–strain curve of the tissue achieved through tension experiments. The frictional force was measured by inserting the needle through precut tissue. Results show that the force model predicts within 0.2 N of experimental needle insertion force and the fracture toughness is primarily affected by the needle diameter and needle edge geometry. On average, the tearing force was found to account for 61% of the total insertion force, the spreading force to account for 18%, and the friction force to account for the remaining 21%.
14 March 2005 in Journal of Manufacturing Science and Engineering
This paper presents a swept envelope approach to determining the optimal tool orientation for five-axis tool-end machining. The swept profile of the cutter is determined based on the tool motion. By analyzing the swept profile against the part geometry, four types of machining errors (local gouge, side gouge, rear gouge, and global collision) are identified. The tool orientation is then corrected to avoid such errors. The cutter’s swept envelope is further constructed by integrating the intermediate swept profiles, and can be applied to NC simulation and verification. This paper analyzes the properties of the swept profile of a general cutter in five-axis tool-end machining. The relation of the swept profile, the part geometry, the tool motion, and the machining errors is developed. Therefore, the error sources can be detected early and prevented during tool path planning. The analytical results indicate that the optimal tool orientation occurs when the curvature of the cutter’s swept profile matches with the curvature of the local part surface. In addition, the optimal cutting direction generally follows the minimum curvature direction. Computer illustrations and example demonstrations are shown in this paper. The results reveal the developed method can accurately determine the optimal tool orientation and efficiently avoid machining errors for five-axis tool-end machining.
6 October 2016 in Journal of Manufacturing Science and Engineering
In this paper, techniques of direct printing of capacitive touch sensors on flexible substrates are presented. Capacitive touch sensors were fabricated by using electrohydrodynamic inkjet (E-jet) printing onto flexible substrates. Touch pad sensors can be achieved with optimized design of silver nanoink tracks. An analytical model was developed to predict touch pad capacitance, and experiments were conducted to study the effects of sensor design (e.g., number of electrodes, electrode length, and electrode distance) on the capacitance of printed coplanar capacitance touch sensors. Details of the fabrication techniques were developed to enable rapid prototype flexible sensors with simple structure and good sensitivity. The presented techniques can be used for the on-demand fabrication of different conductive patterns for flexible electronics with high resolution and good transparency
14 May 2018 in Journal of Manufacturing Science and Engineering
This paper presents a new spiral smoothing method to generate smooth curved tool paths directly on mesh surfaces. Spiral tool paths are preferable for computer numerical control (CNC) milling, especially for high-speed machining. At present, most spiral tool path generation methods aim mainly for pocketing, and a few methods for machining complex surface also suffer from some inherent problems, such as selection of projecting direction, preprocessing of complex offset contours, easily affected by the mesh or mesh deformation. To address the limitations, a new spiral tool path method is proposed, in which the radial curves play a key role as the guiding curves for spiral tool path generation. The radial curve is defined as one on the mesh surface that connects smoothly one point on the mesh surface and its boundary. To reduce the complexity of constructing the radial curves directly on the mesh surface, the mesh surface is first mapped onto a circular region. In this region, the radial lines, starting from the center, are planned and then mapped inversely onto the mesh surface, thereby forming the desired radial curves. By traversing these radial curves using the proposed linear interpolation method, a polyline spiral is generated, and then, the unfavorable overcuts and undercuts are identified and eliminated by supplementing additional spiral points. Spline-based technique of rounding the corners is also discussed to smooth the polyline spiral, thereby obtaining a smooth continuous spiral tool path. This method is able to not only greatly simplify the construction of radial curves and spiral tool path but also to have the ability of processing and smoothing complex surfaces. Experimental results are presented to validate the proposed method.
1 March 2006 in Virtual and Physical Prototyping
This paper presents a new method of using the tri-dexel volumetric models and a haptics force feedback for virtual prototyping and manufacturing planning. In the proposed method, the initial polyhedral surface model is converted to a tri-dexel volumetric model by using a depth-peeling dexelization algorithm. In the virtual prototyping process, the tri-dexel volumetric model is updated by the swept volume of a moving cutter via a haptic force feedback interface device. A collision detection algorithm is proposed for the virtual sculpting and the pencil-cut planning with real-time haptic force feedback to the users. Tool paths are generated for machining the virtual sculpted parts via the simulation and verification on a virtual CNC machine tool before they are actually machined. Computer implementation and practical examples are also presented in this paper. The proposed method enables the haptic-aided virtual prototyping and manufacturing planning of complex surface parts.
21 September 2016 in Journal of Manufacturing Science and Engineering
In this paper, a rapid prototyping method for fabrication of highly conductive micropatterns on insulating substrates was developed and evaluated. Sub-20 μm microstructures were printed on flexible insulating substrates using alternating current (AC) modulated electrohydrodynamic jet (e-jet) printing. The presented technique resolved the challenge of current rapid prototyping methods in terms of limited resolution and conductivity for microelectronic components for flexible electronics. Significant variables of fabrication process, including voltage, plotting speeds, curing temperature, and multilayer effect, were investigated to achieve reliable printing of silver tracks. Sub-20 μm silver tracks were successfully fabricated with resistivity about three times than bulk silver on flexible substrates, which indicates the potential applications of electrohydrodynamic printing in flexible electronics and medical applications, such as lab-on-chip systems.