Mesti Nadya

Mesti Nadya

Auto-generated profile, based on publicly available information

Mesti Nadya

Universitas Merdeka Malang

Research Focus & Metrics

Academic Career Length

1Year (2026-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 August 2026 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
PSPungky Eka Setyawan
Pungky Eka Setyawan
ASAgus Suprapto
Agus Suprapto
DADjoko Andrijono
Djoko Andrijono
ISIgnasius Sandrianus Jono Suarao
Ignasius Sandrianus Jono Suarao
IWIke Widyastuti
Ike Widyastuti
MNMesti Nadya
Mesti Nadya
The object of this research is the pack carburizing of ST 37 low-carbon steel using activated carbon derived from catfish bone waste as a sustainable carburizing medium. ST 37 has low surface hardness, and it is not established how carburizing temperature and holding time govern the resulting hardness and microstructure when a fish-bone-derived carbon is used. Specimens were carburized at 800°C and 875°C for 45, 90, and 115 minutes, followed by water quenching; surface hardness was measured on the Rockwell B scale and the case region was examined by optical microscopy. At 800°C the surface hardness increased from 53.33 to 87.00 HRB as the holding time rose from 45 to 115 minutes, with the case microstructure progressing from ferrite with coarse pearlite to fine pearlite and then to a finer ferrite-carbide constituent. At 875°C the hardness reached 98.33 HRB at every holding time, with the case transforming to a fine, dark-etching ferrite-carbide constituent; this value lies at the upper limit of the Rockwell B scale, so it represents the maximum measurable, not the true, case hardness, and temperature exerted a stronger influence than time. No fully martensitic case formed, which is consistent with the low hardenability of ST 37 and is favorable because hardness is raised without a brittle case. Unlike conventional carburizing that relies on commercial charcoal, the present medium uses fish-bone waste and reaches maximum hardness at 875°C in 45 minutes. These findings apply to small-scale surface hardening of low-carbon steel where fish-bone waste is locally available and a tough, wear-resistant surface is required. The results confirm that catfish bone waste can serve as a low-cost, sustainable carburizing medium for low-carbon steel

26 February 2026 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
ASAgus Suprapto
Agus Suprapto
JJJumiadi Jumiadi
Jumiadi Jumiadi
PSPungky Eka Setyawan
Pungky Eka Setyawan
MNMesti Nadya
Mesti Nadya
SSSergius Sadu
Sergius Sadu
The object of this study is a medium-carbon gear steel commonly used for sprockets and gears in mechanical drive systems. The problem to be solved in this study is the limited understanding of the integrated effect of austenitizing temperature, sprocket rotation speed, and quenching medium on surface hardness and microstructural evolution, that makes parameter selection of flame hardening in industry does not optimum. The experiments were conducted by heating the medium-carbon gear steel into austenitizing temperatures of 850°C and 900°C, rotation speeds of 1503 rpm and 1977 rpm, and using water and oil as quenching medium. Specimens were evaluated by using Rockwell hardness tester (B scale) and optical microscopy. The result of this study reveals that the highest surface hardness of 120.08 HRB is achieved at austenitizing temperature of 900°C, rotation speed of 1503 rpm, and quenched by using water. This is also supported by the result of microstructural observations which show very fine martensite. The surface hardening is most affected by quenching medium, while rotation speed has no significant effect on the hardness enhancement. At austenitizing temperature of 900°C, the steel has been in austenite phase, so the increasing rotation speed reduces hardness due to excessive heat input and austenite grain coarsening. The distinctive feature of these results lies in the identification of interaction mechanisms between thermal exposure time and cooling rate. The findings can be practically applied to medium-carbon gear steel components subjected to controlled flame hardening with continuous rotation at speeds of 1503–1977 rpm, followed by water or oil quenching, particularly in small- and medium-scale industrial heat treatment of gears and sprockets