Wanchai Khamsen

Wanchai Khamsen

Auto-generated profile, based on publicly available information

Wanchai Khamsen

Faculty of Engineering, Rajamangala University of Technology Lanna Lampang, Lampang, Thailand

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 March 2025 in IEEE Sensors Journal
Verified
Journal Article
Open access
AAAPINAN AURASOPON
APINAN AURASOPON
WKWanchai Khamsen
Wanchai Khamsen
Chiraphon TakeangChiraphon Takeang
Chiraphon Takeang
Jaime LloretJaime Lloret
Jaime Lloret
This paper introduces a simplified 2-wire measurement system for accurate resistance measurement of resistive sensors, leveraging the Anderson current loop. The proposed configuration features a precision reference resistor (Rref) and two diodes (D1 and D2), directly interfaced with the Analog-to-Digital Converter (ADC) and output pins of a microcontroller, eliminating the need for external stabilization resistors. Utilizing ratiometric voltage measurements and an adaptive tuning factor, the system effectively compensates for lead wire resistance and diode mismatches. A prototype implemented with an ATmega2560 microcontroller demonstrates accurate resistance measurements in the range of 60–320 Ω, corresponding to a Pt100 sensor, achieving an uncertainty error of less than 0.13% for a lead wire resistance of 4.87 Ω and 0.15% for 10.0 Ω. Experimental results confirm the system’s precision and reliability over long lead lengths, offering a cost-effective and robust solution for industrial and remote sensing applications requiring accurate temperature measurements.

11 June 2025 in IEEE Transactions on Instrumentation and Measurement
Verified
Journal Article
Closed access
WKWanchai Khamsen
Wanchai Khamsen
AAAPINAN AURASOPON
APINAN AURASOPON
Chiraphon TakeangChiraphon Takeang
Chiraphon Takeang
This paper presents a simplified 3-wire and 4-wire measurement method for accurately determining the resistance of sensors, such as RTDs, using an Anderson current loop configuration. The proposed system employs a resistance-to-voltage conversion approach, ensuring high accuracy and simplicity while eliminating the need for additional components such as capacitors, op-amps, or complex timing circuits commonly found in resistance-to-time conversion techniques. Additionally, a tuning technique is incorporated to compensate for Analog-to-Digital Converter (ADC) errors, reference resistance deviations, and lead-wire mismatches, thereby improving measurement precision. This tuning technique requires an initial calibration to determine optimal correction factors, tailored to specific hardware and wiring conditions. A prototype was developed using a commercial ATmega2560 microcontroller with 10-bit ADCs to measure resistances ranging from 50–317 Ω, corresponding to a Pt100 thermal sensor, under varying lead-wire resistances. Experimental results, incorporating tuning factor calibration, demonstrate that the proposed technique achieves a relative uncertainty error below 0.1% for both 3-wire and 4-wire configurations, ensuring accurate and reliable measurements even in the presence of lead-wire variations.

15 January 2025 in IEEE Sensors Journal
Verified
Journal Article
Closed access
AAAPINAN AURASOPON
APINAN AURASOPON
WKWanchai Khamsen
Wanchai Khamsen
CTChiraphon Takeang
Chiraphon Takeang
TTTaweesak Thongsan
Taweesak Thongsan
Jaime LloretJaime Lloret
Jaime Lloret
This research proposes a method to enhance the accuracy of resistance measurements for Resistive Sensors (Rx) using voltage divider and Anderson current loop circuits connected to the Analog-to-Digital Converter (ADC) of a microcontroller. Traditional circuits use a fixed reference resistor (Rref), which causes significant errors when the sensor's voltage drop differs greatly from the reference resistor. To address this, an Adaptive Reference Resistor (ADRR) using a Digital Potentiometer (DPOT) is introduced. The voltage drop across the resistive sensor is used to determine the control code for the DPOT. This adjusts the reference resistance to be close to sensor resistance. Moreover, the introduction of the Tuning Factor (k) for calibrating the measurement system significantly reduces errors. The experiment utilized a MCP41010 DPOT with 256 steps, whose resistance was measured and calibrated by a factor, k. Known resistances were used for accuracy testing within the range of 100 - 9,960 Ω. According to the results, setting the reference resistance interval to 100 Ω led to an error of less than 0.45% for the voltage divider circuit across the measurement range. Meanwhile, the series circuit based on the Anderson current loop demonstrated an error of less than 0.35%.

1 April 2025 in International Journal of Electrical and Computer Engineering (IJECE)
Verified
Journal Article
Open access
PDF file
WKWanchai Khamsen
Wanchai Khamsen
Chiraphon TakeangChiraphon Takeang
Chiraphon Takeang
TJThawinan Janthawang
Thawinan Janthawang
AAAPINAN AURASOPON
APINAN AURASOPON
This article presents a novel multi-objective economic load dispatch solution with the bee colony optimization method. The purposes of this research are to find the lowest total power generation cost and the lowest total power loss at the transmission line. A swarm optimization method was used to consider the non-smooth fuel cost function characteristics of the generator. The constraints of economic load dispatch include the cost function, the limitations of generator operation, power losses, and load demand. The suggested approach evaluates an IEEE 5, 26, and 118 bus system with 3, 6, and 15 generating units at 300, 1,263, and 2,630 megawatt (MW) and uses a simulation running on the MATLAB software to confirm its effectiveness. The outcomes of the simulation are compared with those of the exchange market algorithm, the cuckoo search algorithm, the bat algorithm, the hybrid bee colony optimization, the multi-bee colony optimization, the decentralized approach, the differential evolution, the social spider optimization, and the grey wolf optimization. It demonstrates that the suggested approach may provide a better-quality result faster than the traditional approach.

1 May 2011
Verified
Conference Paper
Closed access
WKWanchai Khamsen
Wanchai Khamsen
AAAPINAN AURASOPON
APINAN AURASOPON
WSWorawat Sa-ngiamvibool
Worawat Sa-ngiamvibool
SKSupaporn Kaittisin
Supaporn Kaittisin
This paper presents the technique for selecting the parameters based on PWM buck AC chopper. This results the optimal capacitor filter that produces the phase angle of input current in phase with that of input voltage. Therefore, the converter operates at unity input power factor. The simulation results by Pspice program are used to verify the proposed technique.