6 May 2019 in IEEE Transactions on Power Electronics
This paper proposes an improved LLC resonant converter with reconfigurable hybrid voltage multiplier (RHVM) for wide output voltage range applications. By adopting three legs and two active switches, the rectifier can be reconfigured to three configurations, i.e. full-bridge rectifier (FBR), hybrid voltage-multiplier rectifier (HVMR) and voltage-multiplier rectifier (VMR), covering the range of more than three times of the minimum output voltage. Compared with conventional LLC converter, the operating range of each configuration is narrowed so that the magnetizing inductance is optimized and switching frequency range is narrowed to achieve higher efficiency. Pulse width plus pulse frequency modulation strategy is employed to achieve smooth transition between these operation modes. Zero-voltage switching of all power MOSFETs and zero-current switching of all secondary-side diodes are achieved as well. Detailed operational principles, characteristics, design consideration and control stagey of the proposed converter are analyzed. A 3.3kW 150V-450V output prototype is built and tested to verify the effectiveness and advantages of the proposed converter.
28 May 2020 in IEEE Transactions on Power Electronics
A single-stage single-phase isolated bidirectional microinverter based on voltage-in-phase PWM (VIP-PWM) controlled resonant converter is proposed in this paper. With the VIP-PWM control, the voltage conversion ratio of the resonant converter can be regulated from zero to infinite, theoretically, which means the VIP-PWM is suitable for wide voltage range applications, such as single-stage isolated inverters. Moreover, the voltage conversion ratio of the resonant converter is only determined by the equivalent duty cycle and free of the value and direction of the transferred power. Therefore, the value and direction of the power flow can be changed smoothly, which makes the proposed converter suitable for bidirectional DC/AC power conversion. Accordingly, a simple unified current controller can be employed for both inverter mode and rectifier mode. In addition, soft switching can be achieved during most of the grid period and high efficiency can be achieved with the proposed solution. Detailed operation principles, characteristics, design considerations and control strategy of the proposed microinverter are presented. A 300W prototype with an input voltage range of 25V-40V is established and tested to verify the effectiveness and feasibility of the proposed solution.
20 February 2020 in IEEE Journal of Emerging and Selected Topics in Power Electronics
An isolated three-port bidirectional series-resonant converter with first-harmonic-synchronized pulse-width modulation (FHS-PWM) is proposed for energy storage application. With FHS-PWM control, the voltage conversion ratio is only determined by the effective duty cycle and has nothing to do with the amplitude and direction of the transferred power. The operating mode can be transited between forward mode and backward mode automatically and smoothly. The voltage of the output port and the energy storage port can also be regulated individually with decoupling control. Furthermore, with the help of auxiliary inductors, zero-voltage switching (ZVS) of all the switches can also be achieved within the entire operating range. Detailed operation principles, characteristics, design considerations and control strategy of the proposed converter are analyzed. An experimental prototype is built and tested to verify the effectiveness and feasibility of the proposed solution.
1 May 2019 in IET Power Electronics
For applications with hold‐up time requirement, the magnetising inductance of the conventional LLC converter must be designed small enough to provide required peak voltage gain. However, the efficiency in normal operation will be decreased when considering the gain requirement. Here, a family of half‐bridge (HB) LLC resonant converters is proposed for low‐voltage and high‐current applications. In order to provide the required voltage gain, auxiliary switches are introduced into parts of the secondary‐side rectifiers. In the normal state, the auxiliary switches keep off and high efficiency can be achieved since the proposed converter always operates around the resonant frequency. Without considering the voltage gain requirement, soft‐switching is the only consideration for the design of the magnetising inductance. Therefore, circulating current and conduction losses induced by the magnetising inductance can be reduced significantly. During the hold‐up time, the auxiliary switches operate with pulse‐width modulation (PWM) control to provide sufficient voltage gain. Furthermore, matrix transformers are engaged to simplify the winding structure and increase the output current capability. Operation principles, characteristics, and design considerations of the proposed LLC resonant converter are analysed in detail. Experimental results are given to verify the effectiveness and the advantages of the proposed converter.
23 January 2025 in IEEE Transactions on Industry Applications
When the five-phase permanent magnet fault-tolerant servo motor (PMFSM) for aerospace is in the typical condition, rotating over a small position angle range, the motor phase current fluctuates up and down in a small range rather than presenting a sinusoidal waveform. Therefore, the current-based open-circuit (OC) fault diagnosis strategy would be ineffective. The OC fault diagnosis strategy based on the lower power switch voltage and line voltage can only diagnose the power switch OC fault, but not the winding OC fault. Therefore, we propose an OC fault diagnosis strategy based on phase voltage to solve the problem that the present OC fault diagnosis method cannot effectively diagnose the OC faults of power switches and windings under the typical condition of servo motors. The proposed strategy can diagnose not only the single power switch OC fault but also the single winding OC fault under the typical condition. In addition, the proposed strategy can also diagnose OC faults in multiple power switches, OC faults in multiple windings, as well as mixed OC faults in windings and power switches. The simulation results verify that the proposed strategy can quickly and accurately diagnose the OC faults of power switches and windings under the typical condition. The phase voltage diagnosis method used in this paper is the first to be used in the fault diagnosis of five-phase motors. Two thresholds are set by combining the phase voltage to diagnose the winding fault and the power switch fault respectively.
7 March 2025 in IEEE Transactions on Industry Applications
Multi-phase motors are frequently applied in aerospace and other fields requiring high reliability, high torque density, and low torque ripple. In this paper, a high-speed five-phase fault-tolerant permanent magnet (HFFPM) motor design scheme is proposed. Through the slot-pole combination optimization selection, the double-layer fractional slot concentrated winding structure, the surface permanent magnet rotor structure, the rotor magnet centrifugal structure, and other designs, the HFFPM motor has lightweight and high reliability performance. By the rotor magnet centrifugal structure, the back electromotive force, the cogging torque, and the flux density of the HFFPM motor are optimized. Then the electromagnetic performance of the HFFPM motor under the rated working condition is simulated. The results show that the motor designed in this paper can still output stable torque under the condition of high-speed operation, and has good fault tolerance performance. Finally, according to the simulation results, the HFFPM motor prototype is made, and its rotation speed characteristics and EMF are tested to verify the correctness of the theoretical analysis.