7 November 2019 in IEEE/ASME Transactions on Mechatronics
This article describes the design of a new type of knee prosthesis called a stance-control swing-assist (SCSA) knee prosthesis. The device is motivated by the recognition that energetically passive stance-controlled microprocessor-controlled knees (SCMPKs) offer many desirable characteristics, such as quiet operation, low weight, high-impedance stance support, and an inertially driven swing-phase motion. Due to the latter, however, SCMPKs are also highly susceptible to swing-phase perturbations, which can increase the likelihood of falling. The SCSA prosthesis supplements the behavior of an SCMPK with a small motor that maintains the low output impedance of the SCMPK swing state, while adding a supplemental closed-loop controller around it. This article elaborates upon the motivation for the SCSA prosthesis, describes the design of a prosthesis prototype, and provides human-subject testing data that demonstrate potential device benefits relative to an SCMPK during both nonperturbed and perturbed walking.
29 September 2021 in IEEE Transactions on Neural Systems and Rehabilitation Engineering
This paper describes stair ambulation control and functionality of a semi-powered knee prosthesis that supplements nominally passive prosthesis behavior with swing-phase assistance. A set of stair ascent and descent controllers are described. The controllers were implemented in a semi-powered prosthesis prototype, and the prospective benefits of swing assist in stair ambulation were assessed on a group of three participants with unilateral, transfemoral amputation, relative to their respective daily-use prostheses. Results indicate that ambulation with the semi-powered knee resulted in improved stair ascent gait symmetry when compared to the participants’ passive daily-use devices, and increased similitude to healthy stair ascent movement.
2 March 2023 in Wearable Technologies
This article proposes, describes, and tests a swing-assist walking controller for a stance-controlled, swing-assisted knee prosthesis that aims to combine benefits of passive swing mechanics (e.g., quiet operation, biomimetic function, and low power requirements) with benefits of powered swing assistance (e.g., increased robustness of swing-phase motion and specifically increased toe clearance). A three-participant, multislope, multispeed treadmill walking study was performed using the swing-assist prosthesis and controller, as well as using the participants’ prescribed microprocessor knee devices. The swing-assist device and approach were found to improve user minimum foot clearance during walking at slopes and speeds, and also to improve symmetry of knee motion. Hip power inputs from stance knee release to heel strike indicated that, on average, less hip power was required when using the swing-assist prosthesis, indicating that the observed benefits were likely the result of the knee device and its control methodology, rather than a result of increased hip joint effort.
4 September 2024 in Ocean Engineering
28 July 2025 in IEEE Transactions on Energy Conversion
Control co-design (CCD) in Wave Energy Converters (WECs) integrates the controller, power take-off (PTO), and buoy models during system design to optimize power output. Using the bi-conjugate impedance matching principle, this study models the PTO as a two-port network, revealing impedance matching conditions at the input and output ports as a function of the buoy, PTO, and controller. This study examines the pairing of a flywheel-type pitch resonator PTO within a given buoy constrained by limited space and ballast capacity. The results show that physical constraints imposed by the buoy affect PTO performance. While controller tuning achieves optimal output impedance matching and flywheel inertia is maximized within the buoy's limitations, the PTO's input impedance remains smaller than the complex conjugate of the buoy's intrinsic impedance. This mismatch limits the PTO's ability to generate sufficient reaction torque, particularly outside the resonance frequency, resulting in narrow-band power transfer. The findings emphasize the need for PTO design modifications to improve input power transfer. Pendulum-based PTO mechanisms are proposed as alternatives to couple with multiple buoy motion modes and improve wave-to-wire efficiency while respecting system constraints.
12 January 2026 in IEEE Transactions on Energy Conversion
This study compares three power-take-off (PTO) mechanisms for wave energy converters—a flywheel-type pitch resonator and two pendulum variants (normal and inverted)—all designed to fit within a fixed envelope. Performance is assessed via linear frequency-domain models and bi-conjugate impedance matching under a representative sea state. The inverted-pendulum PTO achieves 27.9% of the incident wave energy, versus 16.5% for the normal pendulum and 4.2% for the flywheel—that is, 6.6 × and 3.9 × improvements, respectively. These gains arise because pendulum-based systems generate higher torque for a given buoy motion and maintain impedance matching across a wider frequency band. Parametric studies of mass, pendulum arm length, spring stiffness, generator friction, and motor constant quantify the impact of key design choices on power output. By locating the pendulum pivot near the buoy’s center of gravity and positioning the center of rotation below the COG, surge–pitch coupling is improved and energy transfer is further boosted.