Bo Liu

Bo Liu

Auto-generated profile, based on publicly available information

Bo Liu

Institute of Plasma Physics, Hefei Institutes of Physical Science, Chinese Academy of Sciences 1 , Hefei 230031

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 March 2022 in IEEE Transactions on Plasma Science
Verified
Journal Article
Closed access
PYPuqiong Yang
Puqiong Yang
BLBo Liu
Bo Liu
CJCaichao Jiang
Caichao Jiang
XYXin Yang
Xin Yang
JWJianglong Wei
Jianglong Wei
CHChundong Hu
Chundong Hu
To study the characteristics of radio frequency (RF) power coupling, RF plasma diagnostics, actively cooled tube, and negative ion production, a plasma source was designed as a small-scale test facility. The matching network was carefully designed and successfully applied to the 2-MHz RF plasma source. In this article, the design method of the matching unit will be presented; with the assistance of this matching unit, the RF plasma source was successfully lit and the reflected power was reduced to a very low level. A $V\!\!-\!\!I$ probe was installed in front of or in the rear of the matching network, respectively, to in situ measure the RF voltage, current, and phase angle. The equivalent resistance of the RF plasma source was analyzed in detail. The RF power coupling efficiency was derived in two different methods, and the relationship between the coupling efficiency and the equivalent resistance of the plasma source is verified. At the same time, the equivalent resistance of the plasma source was also collected to optimize the matching unit.

29 July 2025 in Nuclear Fusion
Verified
Journal Article
Open access
XPXufeng Peng
Xufeng Peng
YXYongjian Xu
Yongjian Xu
YLYufan Li
Yufan Li
JWJianglong Wei
Jianglong Wei
GMGuangyong Mei
Guangyong Mei
BWBin Wu
Bin Wu
The uniformity of beam, for large RF negative ion source, is closely related to the plasma uniformity in the extraction region. The six electrostatic probes were installed above the plasma grid (PG) 5 mm to evaluate the plasma uniformity. The influence of RF power, source pressure, magnetic filter field, and bias voltage on the plasma uniformity in the extraction region were analyzed. In the absence of magnetic filter field and bias voltage, the plasma density exhibits good uniformity (>90%), but the uniformity of electron temperature (T e) is poor (>60%). It is mainly caused that the magnetic field was generated by the permanent magnet inside extraction grid (EG). The plasma density and T e can be increased by increasing RF power, but it has little effect on the plasma uniformity. Increasing source pressure can effectively lower T e and slightly improve its uniformity, but the uniformity of plasma density has deteriorated by increasing source pressure. While increasing the PG current effectively reduces the T e in the extraction region, it simultaneously degrades the uniformity of both T e and plasma density due to drift effects. Increasing the bias voltage can increase T e in the extraction region when the PG current is 1200 A, but T e at the bottom increases more significantly, thereby worsening the uniformity of T e. In addition, the electron density (N e) at the top decreases, while the N e at the bottom increases, thereby improving the uniformity of N e. The influence of the magnetic filtered field and bias voltage on the non-uniformity of T e in the extraction region, as observed in the manuscript, is similar to the effect on the non-uniformity of the extracted beam current reported in the literature. These results provide theoretical foundations for optimizing the beam uniformity in large RF negative ion sources.

16 June 2022 in Energies
Verified
Journal Article
Open access
PDF file
WLWei Liu
Wei Liu
BLBo Liu
Bo Liu
YZYuanzhe Zhao
Yuanzhe Zhao
QCQinglong Cui
Qinglong Cui
CHChundong Hu
Chundong Hu
LLLizhen Liang
Lizhen Liang
The RF-driven negative ion source has a steady state characteristic and will be a promising ion source for neutral beam injection (NBI) in the future. Cesium (Cs) injection is an efficient method to enhance the yield of negative ions during plasma discharge. In order to support the engineering and physical research in this field, the Cs oven prototype has been developed for negative ion source based neutral beam injector at ASIPP. This article presents the design details of a Cs oven system, including the constant temperature control system, the mechanical structure of Cs oven, and the surface ionization detector (SID). SID is a measurement method for the cesium flux in the nozzle. The experiment results of constant temperature control system show that the control accuracy and function meet the requirements of device operation. Meanwhile, the simulation analysis of Cs vapor concentration has been carried out in this paper. According to the simulation results, the graph of total Cs flux is given in the article, which presents the reference for the subsequent device testing.

14 October 2023 in Fusion Engineering and Design
Verified
Journal Article
Closed access
BLBo Liu
Bo Liu
ZLZhimin Liu
Zhimin Liu
CJCaichao Jiang
Caichao Jiang
JWJianglong Wei
Jianglong Wei
SCShiyong Chen
Shiyong Chen
YXYuanlai Xie
Yuanlai Xie

1 October 2024 in Review of Scientific Instruments
Verified
Journal Article
Closed access
PDF file
BLBo Liu
Bo Liu
XPXufeng Peng
Xufeng Peng
YGYuming Gu
Yuming Gu
YYYuwen Yang
Yuwen Yang
YLYufan Li
Yufan Li
JWJianglong Wei
Jianglong Wei
Due to the high stability and less maintenance, the radio frequency (RF) driven ion source is preferred for the neutral beam injection (NBI) system. In a popular design of the RF ion source for NBI application, a Faraday shield (FS) is installed inside the RF plasma driver to protect the discharge tube. However, the FS also brings some drawbacks, such as lowering the RF power transfer and increasing the processing difficulty. A prototype of the RF plasma driver without FS and with mature manufacturing technology has been developed by using a water-cooled discharge tube. After basic testing, this prototype was further tested under the RF plasma discharge experiments in views of high power, long pulse, and long term. The reliability and its plasma characteristics were the focus of these experiments, also for the hidden issues. The results show that the prototype could generate stable and high-density plasma without any damage or sputtering mark. An RF plasma discharge of 50 kW and 20 s has been achieved. The expected frequency tuning was equally effective on the prototype. Moreover, compared to the RF plasma driver with FS, the prototype could produce higher electron density in the extraction region under the same RF power. Of course, some of the shortcomings of the prototype have also been exposed in the experiments and will be improved in subsequent experiments.

1 November 2021 in Fusion Engineering and Design
Verified
Journal Article
Closed access
PYPuqiong Yang
Puqiong Yang
BLBo Liu
Bo Liu
YZYing Zhang
Ying Zhang
HWHuiling Wei
Huiling Wei
WXWeimin Xuan
Weimin Xuan