1 July 2016 in Journal of the Electrochemical Society
One of the biggest causes of degradation in lithium-ion batteries is elevated temperature. In this study we explored the effects of cell surface cooling and cell tab cooling, reproducing two typical cooling systems that are used in real-world battery packs. For new cells using slow-rate standardized testing, very little difference in capacity was seen. However, at higher rates, discharging the cell in just 10 minutes, surface cooling led to a loss of useable capacity of 9.2% compared to 1.2% for cell tab cooling. After cycling the cells for 1,000 times, surface cooling resulted in a rate of loss of useable capacity under load three times higher than cell tab cooling. We show that this is due to thermal gradients being perpendicular to the layers for surface cooling leading to higher local currents and faster degradation, but in-plane with the layers for tab cooling leading to more homogenous behavior. Understanding how thermal management systems interact with the operation of batteries is therefore critical in extending their performance. For automotive applications where 80% capacity is considered end-of-life, using tab cooling rather than surface cooling would therefore be equivalent to extending the lifetime of a pack by 3 times, or reducing the lifetime cost by 66%.
10 October 2018 in Journal of the Electrochemical Society
Lithium ion batteries are increasingly important in large scale applications where thermal management is critical for safety and lifetime. Yet, the effect of different thermal boundary conditions on the performance and lifetime is still not fully understood. In this work, a two-dimensional electro-thermal model is developed to simulate cell performance and internal states under complex thermal boundary conditions. Attention was paid to model, not only the electrode stack but also the non-core components (e.g. tab weld points) and thermal boundaries, but also the experiments required to parameterize the thermal model, and the reversible heat generation. The model is comprehensively validated and the performance of tab and surface cooling strategies was evaluated across a wide range of operating conditions. Surface cooling was shown to keep the cell at a lower average temperature, but with a large thermal gradient for high C rates. Tab cooling provided much smaller thermal gradients but higher average temperatures caused by lower heat removing ability. The thermal resistance between the current collectors and tabs was found to be the most significant heat transfer bottleneck and efforts to improve this could have significant positive impacts on the performance of li-ion batteries considering the other advantages of tab cooling.
1 February 2020 in eTransportation
3 July 2019 in Journal of the Electrochemical Society
Lithium-ion battery development is conventionally driven by energy and power density targets, yet the performance of a lithium-ion battery pack is often restricted by its heat rejection capabilities. It is therefore common to observe elevated cell temperatures and large internal thermal gradients which, given that impedance is a function of temperature, induce large current inhomogeneities and accelerate cell-level degradation. Battery thermal performance must be better quantified to resolve this limitation, but anisotropic thermal conductivity and uneven internal heat generation rates render conventional heat rejection measures, such as the Biot number, unsuitable. The Cell Cooling Coefficient (CCC) is introduced as a new metric which quantifies the rate of heat rejection. The CCC (units W.K−1) is constant for a given cell and thermal management method and is therefore ideal for comparing the thermal performance of different cell designs and form factors. By enhancing knowledge of pack-wide heat rejection, uptake of the CCC will also reduce the risk of thermal runaway. The CCC is presented as an essential tool to inform the cell down-selection process in the initial design phases, based solely on their thermal bottlenecks. This simple methodology has the potential to revolutionise the lithium-ion battery industry.
1 October 2017 in Journal of Energy Storage
21 August 2019 in Journal of the Electrochemical Society
Cooling electrical tabs of the cell instead of the lithium ion cell surfaces has shown to provide better thermal uniformity within the cell, but its ability to remove heat is limited by the heat transfer bottleneck between tab and electrode stack. A two-dimensional electro-thermal model was validated with custom made cells with different tab sizes and position and used to study how heat transfer for tab cooling could be increased. We show for the first time that the heat transfer bottleneck can be opened up with a single modification, increasing the thickness of the tabs, without affecting the electrode stack. A virtual large-capacity automotive cell (based upon the LG Chem E63 cell) was modelled to demonstrate that optimised tab cooling can be as effective in removing heat as surface cooling, while maintaining the benefit of better thermal, current and state-of-charge homogeneity. These findings will enable cell manufacturers to optimise cell design to allow wider introduction of tab cooling. This would enable the benefits of tab cooling, including higher useable capacity, higher power, and a longer lifetime to be possible in a wider range of applications.