Pablo Carpio

Pablo Carpio

Auto-generated profile, based on publicly available information

Pablo Carpio


Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 December 2016 in Surface and Coatings Technology
Verified
Journal Article
Open access
PCP. Carpio
P. Carpio
MSM.D. Salvador
M.D. Salvador
Amparo BorrellAmparo Borrell
Amparo Borrell
ESE. Sánchez
E. Sánchez
Rodrigo MorenoRodrigo Moreno
Rodrigo Moreno
Suspension plasma spraying (SPS) deposition represents an innovative technique to produce coatings that exhibit improved properties. However, the key to obtain coatings with superior functional properties relies on the investigation of the suspensions as starting materials. For this reason, the present work deals with the suspension preparation for SPS process and its influence on the resulting coatings. Laboratory-prepared 60/40 wt% alumina-zirconia suspensions were concentrated to avoid energy loss and were then successfully deposited by SPS technique. The liquid used was water instead of ethanol due to economical, environmental and safety reasons. The preparation of the suspension plays an important role in SPS process since stable and well-dispersed water suspensions are difficult to obtain. For this reason, colloidal behaviour characterisation of the starting particles as well as rheological optimisation of the feedstock suspensions were addressed in this research. Suspensions with different solid loadings (up to 30 vol.% or 72 wt%) were deposited using several spraying distances. All coatings displayed a bimodal microstructure consisting in partially melted zones surrounded by a fully melted matrix. α-Al2O3 and t’-ZrO2 constituted the main crystalline phases, but differences in the microstructure and properties of the coatings were observed. From these results, some relations between starting suspension and spraying parameters with coating characteristics were found. Thus the optimal spraying distance becomes shorter when the suspension solid loading increases.This work has been supported by the Spanish Ministry of Economy and Competitiveness, MINECO, (project MAT2015-67586-C3-R). M.D. Salvador thanks to CAPES – Programa Ciências sem Fronteiras (Brazil) for the concession of a PVE project Nº A086/2013. A. Borrell acknowledges the MINECO for her Juan de la Cierva-Incorporación contract (IJCI-2014-19839) and the Program to Support Research and Development (PAID-00-15) of the Universitat Politècnica de València

1 August 2019 in Surface and Coatings Technology
Verified
Journal Article
Closed access
PCPablo Carpio
Pablo Carpio
RCRolando T. Candidato
Rolando T. Candidato
Lech PawlowskiLech Pawlowski
Lech Pawlowski
MSMaría Dolores Salvador
María Dolores Salvador

22 February 2016 in Journal of Thermal Spray Technology
Verified
Journal Article
Open access
PDF file
PCPablo Carpio
Pablo Carpio
EEEmilio Rayón Encinas
Emilio Rayón Encinas
MSMaría Dolores Salvador
María Dolores Salvador
Luca LusvarghiLuca Lusvarghi
Luca Lusvarghi
ESEnrique Sánchez
Enrique Sánchez
Double-layer and graded composite coatings of yttria-stabilized zirconia were sprayed on metallic substrates by atmospheric plasma spray. The coating architecture was built up by combining two different feedstocks: one micro- and one nanostructured. Microstructural features and mechanical properties (hardness and elastic modulus) of the coatings were determined by FE-SEM microscopy and nanoindentation technique, respectively. Additional adherence and scratch tests were carried out in order to assess the failure mechanisms occurring between the layers comprising the composites. Microstructural inspection of the coatings confirms the two-zone microstructure. This bimodal microstructure which is exclusive of the layer obtained from the nanostructured feedstock negatively affects the mechanical properties of the whole composite. Nanoindentation tests suitably reproduce the evolution of mechanical properties through coatings thickness on the basis of the position and/or amount of nanostructured feedstock used in the depositing layer. Adhesion and scratch tests show the negative effect on the coating adhesion of layer obtained from the nanostructured feedstock when this layer is deposited on the bond coat. Thus, the poor integrity of this layer results in lower normal stresses required to delaminate the coating in the adhesion test as well as minor critical load registered by using the scratch test.

6 October 2018 in Surface and Coatings Technology
Verified
Journal Article
Closed access
RCRolando T. Candidato
Rolando T. Candidato
JOJose Presiphil Ontolan
Jose Presiphil Ontolan
PCPablo Carpio
Pablo Carpio
Lech PawlowskiLech Pawlowski
Lech Pawlowski
RVReynaldo M. Vequizo
Reynaldo M. Vequizo

1 August 2019 in Surface and Coatings Technology
Verified
Journal Article
Closed access
PCPablo Carpio
Pablo Carpio
Lech PawlowskiLech Pawlowski
Lech Pawlowski
BPBernard Pateyron
Bernard Pateyron

29 March 2021 in Coatings
Verified
Journal Article
Open access
PDF file
Amparo BorrellAmparo Borrell
Amparo Borrell
PCPablo Carpio
Pablo Carpio
MSMaria Dolores Salvador
Maria Dolores Salvador
DMDavid Busquets Mataix
David Busquets Mataix
VCVíctor Carnicer
Víctor Carnicer
MTMaría José Orts Tarí
María José Orts Tarí
Al2O3/TZ-3YS coatings developed by suspension plasma spraying were studied in the present work. Mechanical and thermal characterization was realized to evaluate the suitability of thermal barrier coatings. In addition, SiC particle reinforcement was evaluated for its effect on the mechanical properties of the coating. The problem with SiC reinforcement is its high melting point that causes a large amount of unmolten material to be deposited on the coating. One possible solution followed in the present study consists of including fructose as an additive in order to modify the suspension characteristics. The results conclude that the use of fructose as an additive increases the mechanical and thermal properties (from 1.0 to 1.6 W/m·K), since the microstructure is modified, and results in a lower porosity (17%) compared to the SiC coating (25%).