Limin Qi

Limin Qi

Auto-generated profile, based on publicly available information

Limin Qi

School of Engineering, Zhejiang Key Laboratory of3D Micro/Nano Fabrication and Characterization, Westlake University, Hangzhou, Zhejiang, China

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 October 2024 in IEEE Transactions on Instrumentation and Measurement
Verified
Journal Article
Closed access
RZRui Zheng
Rui Zheng
LQLimin Qi
Limin Qi
SLSizhuo Li
Sizhuo Li
ZGZhihua Gan
Zhihua Gan
DZDing Zhao
Ding Zhao
MQMin Qiu
Min Qiu
Liquid nitrogen (LN2) typically acts as a coolant in ice-assisted electron-beam lithography (iEBL) systems, so that the cryostage temperature cannot be lower than 77 K. To condense more gaseous precursors such as carbon dioxide in a high vacuum environment, a cooling system which does not rely on LN2 is necessary. In this paper, we integrate a Gifford-McMahon cryocooler into the iEBL system, which can cool down samples from room temperature to 21 K in 2.25 hours. The cold head and sample holder reach minimum temperatures of 5.37 ± 0.012 K and 19.14 ± 0.009 K respectively, which lies within the temperature zone of liquid hydrogen. Furthermore, a gas-gap isolation system and discrete rotary valve are employed to minimize the vibration effects on the scanning electron microscope, with the vibration being limited to about 30 nm. Finally, carbon dioxide has been investigated as the precursor, revealing itself as the second positive resist in iEBL, with a critical dose one order of magnitude less than water ice. Gold nanostructures are also successfully fabricated using such a resist. Our system achieves the lowest temperature in iEBL system to date, substantially expanding the range of precursors that can be used in iEBL.

1 August 2024 in Review of Scientific Instruments
Verified
Journal Article
Closed access
PDF file
HPHaiyue Pei
Haiyue Pei
LQLimin Qi
Limin Qi
YLYihan Lu
Yihan Lu
DLDongli Liu
Dongli Liu
JZJiakai Zhu
Jiakai Zhu
MQMin Qiu
Min Qiu
Efficient thermal management is essential for low-temperature optoelectronic devices. Traditional liquid nitrogen (LN2) cooling presents challenges such as frequent replenishment needs and limited operational duration. This study introduces micromachined Joule–Thomson (MJT) cooling as a superior alternative for temperature regulation in optoelectronic devices. We evaluated the thermal and optical performance of MJT cooling for a CdSe/ZnS quantum dot (QD) sample within a temperature range of 120–300 K. Thermal analysis showed that with a single 50 l nitrogen refill, the MJT system can operate continuously for over one week, surpassing the LN2 system by 11 times. The temperature stability was affected little by laser irradiation, with a <0.2 K rise at 5 mW of laser power. In addition, the MJT cooling led to an average blueshift of 1–3 meV in the emission peak of QDs and 0.3–2.3 meV reduced spectral broadening compared to LN2, attributed to a smaller sample-to-cold-stage temperature gap of about 8–9 K in the MJT setup. The standard deviations of peak energy and FWHM are in the order of E − 1 meV magnitude, demonstrating a comparable thermal uniformity compared to LN2. The vibration spectra obtained for both vertical and horizontal directions reveal the superior low-vibration characteristics of MJT cooling. These findings validate MJT cooling as a superior and reliable strategy for the thermal management of optoelectronics, ensuring prolonged operational durations, reliable temperature stability, enhanced temperature precision, high thermal homogeneity, and low vibrations.