Ali Vala Mizrak

Ali Vala Mizrak

Auto-generated profile, based on publicly available information

Ali Vala Mizrak

Electrochemical Energy Systems Laboratory Department of Mechanical Engineering and Mechanics Drexel University Philadelphia PA 19104 USA

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2021 in Journal of the Electrochemical Society
Verified
Journal Article
Closed access
AMAli Vala Mizrak
Ali Vala Mizrak
SUSimge Uzun
Simge Uzun
BABilen Akuzum
Bilen Akuzum
LALutfi Agartan
Lutfi Agartan
Yury GogotsiYury Gogotsi
Yury Gogotsi
EKE. Caglan Kumbur
E. Caglan Kumbur
In this work, Ti 3 C 2 T x MXene was investigated as electrocatalyst material for the anodic V 2+ /V 3+ reaction in vanadium redox flow batteries (VRFBs). A simple drop coating process was established using additive-free, aqueous MXene dispersions to fabricate MXene-coated carbon paper electrodes. The performance of Ti 3 C 2 T x as an anodic electrocatalyst was studied using cyclic voltammetry and electrochemical impedance spectroscopy in a three-electrode cell. Furthermore, flow battery testing was performed to determine the performance of the modified electrodes. At a current density of 50 mA cm −2 , the electrode with Ti 3 C 2 T x loading of 0.2 mg cm −2 enabled a 7% higher energy efficiency and 22% higher electrolyte utilization rate than the pristine electrode. At a higher current density (100 mA cm −2 ), the energy efficiency and electrolyte utilization were increased by 17% and 46%, respectively. At 50% SOC, the coated electrode was able to reach a limiting current density of 220 mA cm −2 while maintaining a voltaic efficiency above 80%, whereas the pristine electrode could only reach up to 160 mA cm −2 at the same voltaic efficiency. The improved performance was mainly attributed to the enhanced electrode kinetics, increased electrochemically active surface area, and improved wetting properties due to the addition of Ti 3 C 2 T x nanoflakes.

13 February 2025 in Electrochimica Acta
Verified
Journal Article
Closed access
AMAli Vala Mizrak
Ali Vala Mizrak
HSHuseyin Engin Sever
Huseyin Engin Sever
JEJonathan C. Ehring
Jonathan C. Ehring
KMKyle Matthews
Kyle Matthews
IRIryna Roslyk
Iryna Roslyk
EKEmin Caglan Kumbur
Emin Caglan Kumbur

27 October 2022 in Batteries & Supercaps
Verified
Journal Article
Closed access
AMAli Vala Mizrak
Ali Vala Mizrak
JEJonathan C. Ehring
Jonathan C. Ehring
MSMikhail Shekhirev
Mikhail Shekhirev
RLRobert W. Lord
Robert W. Lord
BABilen Aküzüm
Bilen Aküzüm
EKE. Caglan Kumbur
E. Caglan Kumbur

1 July 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
TRTarik Rhadfi
Tarik Rhadfi
BBBapi Bera
Bapi Bera
KOKristen Opperman
Kristen Opperman
AMAli V. Mizrak
Ali V. Mizrak
GGGabriel A. Goenaga
Gabriel A. Goenaga
MMMatthew M. Mench
Matthew M. Mench
Transition-metal-substituted magnetite nanocatalysts show promise as bifunctional electrocatalysts for both the oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) in energy conversion and storage technologies. Here, we describe a simple one-step polyol synthesis method for producing Mn-substituted magnetite (MnₓFe₃₋ₓO₄, 0 ≤ x ≤ 1) nanocatalysts with controlled size (7-10 nm), composition, and crystal structure. This polyol method is a versatile wet-chemistry route that enables simultaneous nucleation and growth of metal precursors at a moderate temperature (175 °C) in diethylene glycol, yielding crystalline spinel-phase nanoparticles without post-synthesis annealing.Systematic variation of the Mn/Fe ratio reveals that Mn substitution modulates the electronic structure, surface chemistry, and catalytic activity for both ORR and OER. X-ray diffraction, transmission electron microscopy, X-ray photoelectron spectroscopy, and electrochemical characterization demonstrate that optimal bifunctional activity occurs at x ≈ 0.4-0.6, where enhanced conductivity and favorable oxidation-state distribution facilitate electron-transfer kinetics. Particle size effects show that smaller nanoparticles (7.3-9.2 nm) exhibit superior mass-normalized activity due to increased surface area.This straightforward synthesis offers a method for creating cost-effective, precious-metal-free bifunctional electrocatalysts for renewable energy applications, such as metal-air batteries, regenerative fuel cells, and water electrolyzers.

19 December 2025 in Journal of Power Sources
Verified
Journal Article
Closed access
JEJonathan C. Ehring
Jonathan C. Ehring
HSHuseyin Engin Sever
Huseyin Engin Sever
AMAli V. Mizrak
Ali V. Mizrak
EKEmin C. Kumbur
Emin C. Kumbur

12 September 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
PSPreetam Sharma
Preetam Sharma
AMAli V. Mizrak
Ali V. Mizrak
ZHZakerie A. Hubbs
Zakerie A. Hubbs
GGGabriel A. Goenaga
Gabriel A. Goenaga
EBEmily Di Bias
Emily Di Bias
MMMatthew M. Mench
Matthew M. Mench
Aluminum–air batteries offer exceptionally high theoretical energy density and rely on an abundant, low-cost metal, but their practical deployment is limited by parasitic corrosion, incomplete aluminum utilization, and transport losses. Here we report a membrane-free aluminum–air flow battery that couples a circulating alkaline electrolyte with stannate-assisted anode stabilization to enable high-power operation without an ion-conducting membrane. By systematically varying cathode oxidant, electrolyte flow rate, and aluminum purity, we show that electrolyte hydrodynamics and anode composition strongly govern cell resistance, interfacial polarization, and aluminum utilization. The optimized cell delivered a peak power density of 1.91 W/cm2 under oxygen operation, which, to the best of the authors’ knowledge, represents the highest peak power density reported to date for an aluminum–air battery, while maintaining a peak power density of 0.63 W/cm2 under air. During galvanostatic discharge at 1000 mA/cm2, aluminum utilization reached 90%, with an aluminum-basis specific capacity of 2674 mAh/g and specific energy of 2840 Wh/kg. Electrochemical characterization revealed that enhanced electrolyte circulation reduces coupled ohmic, interfacial, and transport-associated losses, while aluminum purity strongly influences the evolving anode–electrolyte interface. These results establish membrane-free electrolyte management as an effective strategy for simultaneously achieving high power and efficient aluminum utilization, advancing mechanically rechargeable aluminum–air systems toward practical high-power energy storage.