1 September 2018 in APL Materials
Aerosol-jet printing allows functional materials to be printed from inks with a wide range of viscosities and constituent particle sizes onto various substrates, including the printing of organic thermoelectric materials on flexible substrates for low-grade thermal energy harvesting. However, these materials typically suffer from relatively poor thermoelectric performance, compared to traditional inorganic counterparts, due to their low Seebeck coefficient, S, and electrical conductivity, σ. Here, we demonstrate a modified aerosol-jet printing technique that can simultaneously incorporate well-dispersed high-S Sb2Te3 nanoflakes and high-σ multi-walled carbon nanotubes (MWCNTs) providing good inter-particle connectivity to significantly enhance the thermoelectric performance of poly(3,4-ethylenedioxythiophene) polystyrene sulfonate structures on flexible polyimide substrates. A nominal loading fraction of 85 wt. % yielded a power factor of ∼41 μW/mK2, which is among the highest for printed organic-based structures. Rigorous flexing and fatigue tests were performed to confirm the robustness and stability of these aerosol-jet printed MWCNT-based thermoelectric nanocomposites.
14 October 2019 in Advanced Electronic Materials
Thermoelectric generators (TEGs) operate in the presence of a temperature gradient, where the constituent thermoelectric (TE) material converts heat into electricity via the Seebeck effect. However, TE materials are characterized by a thermoelectric figure of merit (ZT) and/or power factor (PF), which often has a strong dependence on temperature. Thus, a single TE material spanning a given temperature range is unlikely to have an optimal ZT or PF across the entire range, leading to inefficient TEG performance. Compositionally graded organic–inorganic nanocomposites are demonstrated, where the composition of the TE nanocomposite can be systematically tuned along the length of the TEG, in order to optimize the PF along the applied temperature gradient. The nanocomposite composition is dynamically tuned by an aerosol‐jet printing method with controlled in situ mixing capability, thus enabling the realization of such compositionally graded thermoelectric composites (CG‐TECs). It is shown how CG‐TECs can be realized by varying the loading weight percentage of Bi2Te3 nanoparticles or Sb2Te3 nanoflakes within an organic conducting matrix using bespoke solution‐processable inks. The enhanced energy harvesting capability of these CG‐TECs from low‐grade waste heat (<100 °C) is demonstrated, highlighting the improvement in output power over single‐component TEGs.
1 November 2016 in APL Materials
We investigate the electromechanical interactions in individual polyvinylidene fluoride-trifluoroethylene nanowires in response to localized electrical poling via a conducting atomic force microscope tip. Spatially resolved measurements of piezoelectric coefficients and elastic moduli before and after poling reveal a striking dependence on the polarity of the poling field, notably absent in thin films of the same composition. These observations are attributed to the unclamped nature of the nanowires and the inherent asymmetry in their chemical and electrical interactions with the tip and underlying substrate. Our findings provide insights into the mechanism of poling/switching in polymer nanowires critical to ferroelectric device performance.
28 April 2016 in Semiconductor Science and Technology
We report the development of a simple and reliable, front-sided-only fabrication technique for n-type ohmic contacts to two-dimensional electron gases (2DEGs) in undoped GaAs/AlGaAs quantum wells. We have adapted the well-established recessed ohmic contacts/insulated metal gate technique for inducing a 2DEG in an undoped triangular well to also work reliably for undoped square quantum wells. Our adaptation involves a change in the procedure for etching the ohmic contact pits to optimise the etch side-wall profile and depth. As an application of our technique, we present a front-side-gated ambipolar field effect transistor (FET), where both 2D electron and hole gases can be induced in the same quantum well. We present results of low-temperature (0.3 K - 4 K) transport measurements of this device, including assessment of the n-type ohmic contact quality. On the basis of our findings, we discuss why the fabrication of these contacts is difficult and how our technique circumvents the challenges.
4 September 2012 in Physical Review B
We present thermal and electrical transport measurements of low-density (10 m), mesoscopic two-dimensional electron systems (2DESs) in GaAs/AlGaAs heterostructures at sub-Kelvin temperatures. We find that even in the supposedly strongly localized regime, where the electrical resistivity of the system is two orders of magnitude greater than the quantum of resistance , the thermopower decreases linearly with temperature indicating metallicity. Remarkably, the magnitude of the thermopower exceeds the predicted value in noninteracting metallic 2DESs at similar carrier densities by over two orders of magnitude. Our results indicate a new quantum state and possibly a novel class of itinerant quasiparticles in dilute 2DESs at low temperatures where the Coulomb interaction plays a pivotal role. DOI: http://dx.doi.org/10.1103/PhysRevB.86.125406 ©2012 American Physical Society
11 March 2019 in Engineering Biology
The authors describe a thermofluidic chip on which microscale islands of controlled temperature are formed within an open fluidic environment. The chip forms part of the authors’ technology for thermally controlled DNA synthesis, whereby the site‐specific temperature control enables site‐specific addressability of chemical reactions, for example, related to the phosphoramidite cycle. Here, the authors discuss the principle of the chip, supporting the thermal well concept by means of simulations as well as by showing a prototype thermal array device.