Oriented ZnO seed layers were deposited by three different techniques, namely, simple drop casting (DC), sol-gel derived dip coating (DPC) and spin coating of ball-milled ZnO powder solution(BMD) for the subsequent growth of vertically aligned ZnO nanorods along the substrate normal. X-ray diffraction (XRD) analyses revealed that ZnO(DC) seed layer exhibit the highest preferential c-axis texturing among the ZnO seed layers synthesized by different techniques. The Scanning Electron Microscopy (SEM) analysis evident that the morphology of ZnO seed layer surface is compact and coherently carpets the underlying substrate. ZnO nanorods(NRs) were then grown by hydrothermal method atop the ZnO seeded and non-seeded substrates grown by different techniques to elucidate the best ZnO seed layer promoting well-aligned ZnO Nanorods. The presence of c-axis oriented ZnO(DC) seeding layers was found to significantly affect the surface morphology and crystallographic orientation of the resultant ZnO NRs films. The optical band gap of ZnO(DC) seed and ZnO NRs were estimated to be 3.30 eV and in the range of 3.18 – 3.25 eV respectively by using UV-VIS-NIR diffuse reflection spectroscopy. The room temperature photoluminescence analyses revealed that nanostructured ZnO films exhibit a sharp near-band-edge luminescence peak at ∼380 nm consistent with the estimated optical band gap and the ZnO nanorod arrays are notably free from defect-related green-yellow emission peaks.
Herein, paper mill waste sludge (PMS) from two different sources has been investigated to extract calcium hydroxide, Ca(OH) 2 by a facile and inexpensive extraction process. PMS samples, collected from local paper mill plants of Bangladesh, were the main precursors wherein HCl and NaOH were used for chemical treatment. The as-synthesized products were analysed by a variety of characterization tools including X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, Raman spectroscopy, scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) elemental analyses. Our studies confirm that the extracted product contains Ca(OH) 2 as a major content, albeit it also includes CaCO 3 phase owing to the inescapable carbonation process from the surrounding environment. The particle size of the synthesized products is in the range of 450–500 nm estimated from SEM micrographs. The crystallite domain size of the same estimated from XRD analyses and was found to be approximately 47 and 31 nm respectively for product-A and product-B considering major (101) Bragg peak of Ca(OH) 2 . The yield percentage of the isolated products is about 65% for samples collected from both sources.
1 September 2023 in ECS Journal of Solid State Science and Technology
Barium titanate, BaTiO3 (BT), materials have been synthesized by two different routes. One ball-mill-derived (BMD) nanopowder and another precursor-derived (PCD) BT synthesis method were used separately to fabricate BT thin films on stainless steel (SS) and quartz substrates by spin coating. Then thin films from both synthesis routes were characterized by Ultraviolet-Visible-Near Infrared (UV–vis-NIR) Spectroscopy, Field-Emission Scanning Electron Microscopy (FE-SEM), X-ray Diffractometry (XRD), Raman Spectroscopy, and Four-point collinear probe; all carried out at room temperature. Our studies revealed that the PCD synthesis process did not produce the BT phase even under the 900 °C air-annealing condition. In contrast, a homogeneous BT thin film has been formed from the BMD-BT nanopowder. The optical bandgap of BMD-BT thin films was found in the 3.10–3.31 eV range. Finally, a Graphene-Barium Titanate-Graphene (G-BT-G) structure was fabricated on an SS substrate by spin coating at processing temperatures below 100 °C and characterized by two different pieces of equipment: a Potentiostat/Galvanostat (PG-STAT) and a Precision Impedance Analyzer (PIA). The G-BT-G structure exhibited a capacitance of 8 nF and 7.15 nF, a highest dielectric constant of 800 and 790, and a low dielectric loss of 4.5 and 5, investigated by PG-STAT and PIA equipment, respectively.