Tomas Kacetl

Tomas Kacetl

Auto-generated profile, based on publicly available information

Tomas Kacetl

Porsche Engineering, Bietigheim-Bissingen, Germany

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
31 May 2022 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
JKJan Kacetl
Jan Kacetl
Jingyang FangJingyang Fang
Jingyang Fang
TKTomas Kacetl
Tomas Kacetl
Nima TashakorNima Tashakor
Nima Tashakor
SGStefan Goetz
Stefan Goetz
Larger battery packs, an efficient battery management system, highly efficient electromechanical conversion, and fast battery charging are the key factors for extending the drive range of electric vehicles and the expansion of electromobility. We present a novel highly stable modular multilevel powertrain design with a variable dc-bus voltage, active inner battery energy flow control, and reduced filter size. The underlying powertrain design replaces conventional hard-wired batteries by a modular multilevel architecture, thus modularizing the battery pack and increasing the energy efficiency, reducing the output filter size, and providing full control over the output voltage and energy flow of the battery cells. We analyse the large-signal stability of the proposed system and compare it to dc/dc-dc/ac conventional multiconverter powertrains, demonstrating better stability and lower filter requirements. Further, we experimentally evaluate the proposed system structure. In the experimental setup, we achieve stable converter operation with the output filter capacitor reduced by a factor of 24 and the filter inductor reduced by a factor of 17 compared to dc-dc-dc-ac reference system, thereby leading to a significant reduction of system cost, size, and weight.

12 September 2022 in IEEE Access
Verified
Journal Article
Open access
TKTomas Kacetl
Tomas Kacetl
JKJan Kacetl
Jan Kacetl
Nima TashakorNima Tashakor
Nima Tashakor
JFJingyang Fang
Jingyang Fang
SGStefan M. Goetz
Stefan M. Goetz
Modular cascaded circuits offer attractive qualities in reconfigurable battery applications, including improved fault tolerance and flexibility. In contrast to conventional hard-wired dc battery packs, however, cascaded topologies, such as modular multilevel circuits (MMC) with serial or serial and parallel connectivity, load modules with substantial low-frequency current ripple, which generates additional loss and can accelerate battery aging. Recent studies reveal that low-frequency ripple can cause noticeable battery aging, whereas high frequencies are insignificant, presumably mainly as they can be absorbed by the dielectric electrode capacitance, and reduce heating associated with lower high-frequency battery impedance. Previous MMC–battery control methods solely focus on state-of-charge and thermal balancing of individual modules, while the few existing methods for suppressing ripple tend to form low-frequency patterns in the modules’ load, which increase battery cycling as well as loss. This paper presents a ripple-oriented high-bandwidth control technique that minimizes low-frequency components in the module load spectrum and improves battery treatment, while maintaining the average switching frequency. The control method takes limitations related to module data acquisition into account and enhances the feedback bandwidth using observers. It works with a wide range of topologies including modules with series connectivity only as well as series/parallel. The measurements in the laboratory verify the shift of the module load from the 10 – 100 Hz range to ~5 kHz and a reduction of battery losses by up to 20 %.

19 August 2020 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
JKJan Kacetl
Jan Kacetl
TKTomas Kacetl
Tomas Kacetl
MJMalte Jaensch
Malte Jaensch
SGStefan M. Goetz
Stefan M. Goetz
High-power silicon field-effect transistors as well as IGBTs and particularly wide-bandgap semiconductor transistors typically need negative turn-off voltage for a secure off-state, resilience to spurious turn on, and rapid transition through the saturation mode. We present a gate driver configuration with compact and very efficient supply of high-side and low-side of power transistor bridges with asymmetric bipolar control voltages without the need for costly and lossy isolated DCDC converter and only low-voltage active components. The underlying circuit consists of only a few cost-efficient components, its electrical potential is referenced to the source of the controlled semiconductor power switch, and its operation is synchronized with the gate driver out-put. It outcompetes the established use of isolated DCDC converters in gate circuits with negative voltage needs with respect to cost, size, reliability, and efficiency. Importantly, the proposed negative voltage supply allows bootstrapping without need for controllable high-voltage semiconductors for the sake of further cost reduction. We present detailed design rules of the circuit and experimentally validate circuit and control. In the automotive prototype implementation, size of the gate driver supply was reduced by 61 %, cost by 57 % and loss by more than 16%.

19 September 2022 in arXiv
Verified
Preprint
Open access
PDF file
TKTomas Kacetl
Tomas Kacetl
JKJan Kacetl
Jan Kacetl
Nima TashakorNima Tashakor
Nima Tashakor
SGStefan Goetz
Stefan Goetz
Whereas in typical standardized tests batteries are almost exclusively loaded with constant current or relatively slowly changing cycles, real applications involve rapid load ripple, which do not contribute to the net energy. The trend to reduced filter capacitors and even dynamically reconfigurable batteries further increases the ripple. The influence of rippled load on lithium batteries is therefore receiving increased attention. According to recent studies, accelerated ageing strongly depends on the frequency of the ripple. We use electrochemical models to derive a highly simplified regression model that catches the asymptotic behavior and allows parameter identification and calibration to specific cells. The model allows quantitative monitoring of the additional ageing due to ripple current in battery management systems. Furthermore it enables active control of the ageing potential by influencing the frequency content in modern battery systems, such as reconfigurable batteries.